과정의 장
교육 · 트랙 3. 동작과 아키텍처 · 3.6장 (전체 6장)
3.6 예산과 TPM 3:31
도크의 질량을 예비분과 여유분을 포함해 집계한 다음, 기술 성능 척도로 추적합니다.
Holarch 2.13 화면입니다.
학습 내용
- 루트 자산에 수량, 단위, 필요 여유를 지정해 예산 설정하기
- 근거와 함께 값을 입력하고 예비분과 여유가 어떻게 바뀌는지 읽기
- 할당을 설정하고 줄의 여유 상태 읽기
- 임계값, 목표값, 마일스톤, 스냅샷이 있는 TPM 만들기
Bike-Share Dock의 질량 예산을 부품으로부터 개수, 근거, 예비분과 함께 만들고, 할당을 설정하여 여유를 읽은 다음, 임계값, 목표값, 계획된 마일스톤, 스냅샷이 있는 도크 질량의 기술 성능 척도를 만듭니다.
실습
CubeSat EO-1 데모 프로젝트에서 Holarch로 직접 해 보십시오.
- EO-1 데모 프로젝트를 열거나 만드십시오. 프로젝트 관리 → 프로젝트 파일 ▾ → 새 데모 프로젝트 → CubeSat (Guided systems engineering).
- 아키텍처 → 예산 및 TPM을 엽니다. 예산 탭에서 루트로 1 EO-1 Spacecraft를 유지하고 수량을 Power Draw로 바꿉니다.
- 1.1 Payload Camera(6.2 W, 추정값)를 찾아 근거를 측정값으로 바꿉니다. 예비분과 우주선의 여유가 어떻게 바뀌는지 읽습니다.
- 데이터베이스에서 + 새 항목으로 Measure를 만듭니다. 이름
ADCS Mass, 번호TPM-4입니다. Units를kg, Threshold Value를1.35 kg, Objective Value를1.2 kg, Improvement Direction을 Negative로 설정하고, 레이블 TPM을 추가한 다음, specified by로 1.2 ADCS에 연결합니다. - TPM 탭에서 TPM-4 ADCS Mass를 선택합니다. 예산 탭의 ADCS 질량(수량 Mass, CBE + 예비분)을 현재 추정치로 입력하고, + 마일스톤을 클릭해 계획값
1.3 kg인CDR을 추가한 다음, 스냅샷 찍기를 클릭합니다.
TPM-4 ADCS Mass가 상태, 계획 프로필의 CDR 마일스톤, 추정 이력의 스냅샷 지점과 함께 나열되면 완료입니다.
스스로 확인
- 예비분이 값의 근거에 따라 달라지는 이유는 무엇입니까?
- 여유는 어떻게 계산되며, 줄은 언제 경고합니까?
- TPM은 예산에 무엇을 더합니까?
- Holarch에서 Measure를 TPM으로 만드는 것은 무엇입니까?
답 보기
예비분이 값의 근거에 따라 달라지는 이유는 무엇입니까?
추정은 계산보다 불확실하고, 계산은 측정보다 불확실합니다. 근거별 예비분(데모에서는 15, 10, 3%)은 숫자가 불확실할수록 더 많은 여유분을 둡니다.
여유는 어떻게 계산되며, 줄은 언제 경고합니까?
여유는 할당에서 현재 최선 추정치와 예비분을 뺀 값입니다. 여유가 필요 여유보다 작으면 줄에 ▲ 낮음이, 할당을 넘으면 ✕ 초과가 표시됩니다.
TPM은 예산에 무엇을 더합니까?
예산은 오늘의 집계를 보여 줍니다. TPM은 중요한 숫자 하나를 프로젝트 수명 동안 계획 프로필, 임계값, 목표값과 비교해 추적하므로, 위반으로 향하는 추세가 검토 전에 드러납니다.
Holarch에서 Measure를 TPM으로 만드는 것은 무엇입니까?
TPM 레이블입니다. 이 레이블이 있는 Measure는 Threshold Value가 있는 요구사항과 함께 TPM 탭에 나열됩니다.
더 읽어 보기
대본
대본 보기 (내레이션과 화면 내용)
Introduction
Welcome back. A design is only as good as its margins. This last chapter of the track puts numbers on the dock's mass.
You will build a mass budget, and a technical performance measure that tracks it over time.
The budget
Open Architecture, then Budgets. Choose the root asset: the Bike-Share Dock. The quantity is mass, in kilograms. Every part under the dock gets a row.
On screen: Architecture → Budgets → root S.0; unit kg.
Enter each part's mass in the unit value column. A docking bay weighs fifty-five kilograms, and the dock has ten of them, so set its count to ten.
On screen: Docking Bay: 55, count 10.
The kiosk is a hundred and forty kilograms, the charging unit eighty, and the power supply thirty. The dock's row shows the sum of its parts.
On screen: Kiosk 140, Charging Unit 80, Power Supply 30.
Contingency and margin
Each value has a basis: estimated, calculated or measured. Contingency follows the basis, so a guess carries more than a part that has been weighed. Here every value is still an estimate.
On screen: Basis and contingency columns.
Set the allocation on the dock: nine hundred kilograms, the most the installation site can carry. The status says over: with fifteen percent contingency on every estimate, the dock comes to nine hundred and twenty kilograms, twenty over.
On screen: Allocation 900 on S.0 → Over allocation.
The docking bays are the biggest item. Once a bay has been weighed, its basis is measured, and its contingency drops to three percent. Set the docking bay's basis to Measured.
On screen: Docking Bay → Basis: Measured.
Now the dock is forty-six kilograms under its allocation, a margin of five percent. The project asks for ten, so the status still warns: the design needs either lighter parts or a larger allocation.
On screen: Margin 46 kg (5.11%) → Margin below 10%.
A technical performance measure
A budget is today's number. A technical performance measure, a TPM, tracks one critical number over the life of the project. Create a Measure in the Database: Dock Mass, numbered TPM one, in kilograms.
On screen: Database → New Entity: Measure TPM-1 Dock Mass.
Its threshold is nine hundred kilograms, the limit it must not pass, and its objective is eight hundred, the value the design aims for. For mass, lower is better, so its improvement direction is negative.
On screen: Units, Threshold 900, Objective 800, Improvement Direction.
What makes it a TPM is its label. Under Labels, click plus Label, and choose TPM.
On screen: Labels → + Label → TPM.
Back in Budgets, open the TPMs tab. Dock Mass is listed, with its threshold and objective.
On screen: Budgets → TPMs.
Track it
Enter the current estimate from the budget, eight hundred and fifty-four kilograms. Add a milestone: the preliminary design review on the first of December, planned at eight hundred and eighty. Take a snapshot, and today's estimate joins the history. At every review, the chart shows whether the dock is on track, long before anything is built.
On screen: Current estimate; + Milestone; Take Snapshot.
Recap
Let's recap. You built a mass budget from the parts with counts, bases and contingency, set an allocation and read the margin, and created a TPM with a threshold, an objective, a milestone and a snapshot.
That completes Behavior and Architecture. You can now model functions and their flow, action diagrams, allocation, interfaces, simulation, budgets and TPMs.
On screen: Track complete card, then end card.