Holarch
Capítulos del curso

Formación · Curso 3. Comportamiento y arquitectura · Capítulo 3.6 de 6

3.6 Presupuestos y TPM 3:31

Agregar la masa del dock con contingencia y margen, y seguirla después como medida de rendimiento técnico.

Muestra Holarch 2.13.

← 3.5 Simulación · Todos los capítulos

Lo que aprenderá

  • Configurar un presupuesto sobre un activo raíz con una magnitud, una unidad y un margen requerido
  • Introducir valores con una base y observar cómo cambian la contingencia y el margen
  • Fijar una asignación y leer el estado del margen de una línea
  • Crear una TPM con un umbral, un objetivo, un hito y una instantánea

Cree un presupuesto de masa del Bike-Share Dock a partir de sus partes, con cantidades, bases y contingencia, fije una asignación y lea el margen; después cree una medida de rendimiento técnico para la masa del dock con un umbral, un objetivo, un hito planificado y una instantánea.

Archivos de proyecto

  • Proyecto inicial (.holarch.json; Gestionar proyectos → Archivos de proyecto ▾ → Importar proyecto (.json)…)
  • Proyecto terminado (.holarch.json; Gestionar proyectos → Archivos de proyecto ▾ → Importar proyecto (.json)…)

El vídeo se reproduce desde holarch.app; consulte la Política de privacidad.

Práctica

Hágalo usted mismo en Holarch, en el proyecto de demostración CubeSat EO-1.

  1. Abra su proyecto de demostración EO-1 o créelo: Gestionar proyectos → Archivos de proyecto ▾ → Nuevo proyecto de demostración → CubeSat (ingeniería de sistemas guiada).
  2. Abra Arquitectura → Presupuestos y TPM. En la pestaña Presupuesto, mantenga 1 EO-1 Spacecraft como raíz y cambie Magnitud a Power Draw.
  3. Busque 1.1 Payload Camera (6,2 W, Estimado) y cambie su Base a Medido. Observe cómo cambian su contingencia y el margen de la nave.
  4. En la Base de datos, cree una Measure con + Nuevo elemento: ADCS Mass, número TPM-4. Fije Units kg, Threshold Value 1.35 kg, Objective Value 1.2 kg e Improvement Direction Negative, añada la etiqueta TPM y vincúlela a 1.2 ADCS con specified by.
  5. En la pestaña TPM, seleccione TPM-4 ADCS Mass. Escriba la masa del ADCS de la pestaña Presupuesto (Magnitud Mass, CBE + contingencia) como Estimación actual, haga clic en + Hito para añadir CDR con un valor planificado de 1.3 kg y después haga clic en Tomar instantánea.

Habrá terminado cuando TPM-4 ADCS Mass aparezca con un estado, un hito CDR en su perfil planificado y un punto de instantánea en su historial de estimaciones.

Compruebe lo aprendido

  1. ¿Por qué depende la contingencia de la base de un valor?
  2. ¿Cómo se calcula el margen y cuándo avisa una línea?
  3. ¿Qué aporta una TPM a un presupuesto?
  4. ¿Qué convierte una Measure en una TPM en Holarch?
Mostrar las respuestas
  1. ¿Por qué depende la contingencia de la base de un valor?

    Una estimación es menos segura que un cálculo, y un cálculo menos que una medición. La contingencia por base (15, 10 y 3 % en la demostración) reserva más margen donde el número es menos seguro.

  2. ¿Cómo se calcula el margen y cuándo avisa una línea?

    El margen es la asignación menos la mejor estimación actual más la contingencia. Una línea muestra ▲ Bajo cuando el margen está por debajo del margen requerido y ✕ Excedido cuando supera su asignación.

  3. ¿Qué aporta una TPM a un presupuesto?

    Un presupuesto muestra la agregación de hoy. Una TPM sigue un número crítico a lo largo de la vida del proyecto frente a un perfil planificado, un umbral y un objetivo, de modo que una tendencia hacia el incumplimiento se ve antes de las revisiones.

  4. ¿Qué convierte una Measure en una TPM en Holarch?

    La etiqueta TPM. Las Measures que la llevan aparecen en la pestaña TPM, junto con los requisitos que tienen un Threshold Value.

Más información

Transcripción

Mostrar la transcripción (narración y lo que aparece en pantalla)

Introduction

Welcome back. A design is only as good as its margins. This last chapter of the track puts numbers on the dock's mass.

You will build a mass budget, and a technical performance measure that tracks it over time.

The budget

Open Architecture, then Budgets. Choose the root asset: the Bike-Share Dock. The quantity is mass, in kilograms. Every part under the dock gets a row.

On screen: Architecture → Budgets → root S.0; unit kg.

Enter each part's mass in the unit value column. A docking bay weighs fifty-five kilograms, and the dock has ten of them, so set its count to ten.

On screen: Docking Bay: 55, count 10.

The kiosk is a hundred and forty kilograms, the charging unit eighty, and the power supply thirty. The dock's row shows the sum of its parts.

On screen: Kiosk 140, Charging Unit 80, Power Supply 30.

Contingency and margin

Each value has a basis: estimated, calculated or measured. Contingency follows the basis, so a guess carries more than a part that has been weighed. Here every value is still an estimate.

On screen: Basis and contingency columns.

Set the allocation on the dock: nine hundred kilograms, the most the installation site can carry. The status says over: with fifteen percent contingency on every estimate, the dock comes to nine hundred and twenty kilograms, twenty over.

On screen: Allocation 900 on S.0 → Over allocation.

The docking bays are the biggest item. Once a bay has been weighed, its basis is measured, and its contingency drops to three percent. Set the docking bay's basis to Measured.

On screen: Docking Bay → Basis: Measured.

Now the dock is forty-six kilograms under its allocation, a margin of five percent. The project asks for ten, so the status still warns: the design needs either lighter parts or a larger allocation.

On screen: Margin 46 kg (5.11%) → Margin below 10%.

A technical performance measure

A budget is today's number. A technical performance measure, a TPM, tracks one critical number over the life of the project. Create a Measure in the Database: Dock Mass, numbered TPM one, in kilograms.

On screen: Database → New Entity: Measure TPM-1 Dock Mass.

Its threshold is nine hundred kilograms, the limit it must not pass, and its objective is eight hundred, the value the design aims for. For mass, lower is better, so its improvement direction is negative.

On screen: Units, Threshold 900, Objective 800, Improvement Direction.

What makes it a TPM is its label. Under Labels, click plus Label, and choose TPM.

On screen: Labels → + Label → TPM.

Back in Budgets, open the TPMs tab. Dock Mass is listed, with its threshold and objective.

On screen: Budgets → TPMs.

Track it

Enter the current estimate from the budget, eight hundred and fifty-four kilograms. Add a milestone: the preliminary design review on the first of December, planned at eight hundred and eighty. Take a snapshot, and today's estimate joins the history. At every review, the chart shows whether the dock is on track, long before anything is built.

On screen: Current estimate; + Milestone; Take Snapshot.

Recap

Let's recap. You built a mass budget from the parts with counts, bases and contingency, set an allocation and read the margin, and created a TPM with a threshold, an objective, a milestone and a snapshot.

That completes Behavior and Architecture. You can now model functions and their flow, action diagrams, allocation, interfaces, simulation, budgets and TPMs.

On screen: Track complete card, then end card.