Chapitres du cours
Formation · Parcours 3. Comportement et architecture · Chapitre 3.6 sur 6
3.6 Budgets et TPM 3:31
Agréger la masse de la borne avec provision et marge, puis la suivre comme mesure de performance technique.
Montre Holarch 2.13.
Ce que vous allez apprendre
- Configurer un budget sur un asset racine avec une grandeur, une unité et une marge requise
- Saisir des valeurs avec une base et lire comment la provision et la marge évoluent
- Définir une allocation et lire l'état de marge d'une ligne
- Créer une TPM avec un seuil, un objectif, un jalon et un instantané
Construisez un budget de masse du Bike-Share Dock à partir de ses parties, avec nombres, bases et provision, définissez une allocation et lisez la marge, puis créez une mesure de performance technique pour la masse de la borne avec un seuil, un objectif, un jalon prévu et un instantané.
Fichiers de projet
- Projet de départ (.holarch.json ; Gérer les projets → Fichiers de projet ▾ → Importer un projet (.json)…)
- Projet terminé (.holarch.json ; Gérer les projets → Fichiers de projet ▾ → Importer un projet (.json)…)
La vidéo est diffusée depuis holarch.app ; voir la Politique de confidentialité.
Pratique
Faites-le vous-même dans Holarch, sur le projet de démonstration CubeSat EO-1.
- Ouvrez votre projet de démonstration EO-1, ou créez-le : Gérer les projets → Fichiers de projet ▾ → Nouveau projet de démonstration → CubeSat (ingénierie système guidée).
- Ouvrez Architecture → Budgets et TPM. Dans l'onglet Budget, gardez 1 EO-1 Spacecraft comme racine et changez Grandeur en Power Draw.
- Trouvez 1.1 Payload Camera (6,2 W, Estimée) et changez sa Base en Mesurée. Observez comment sa provision et la marge du satellite évoluent.
- Dans la Base de données, créez une Measure avec + Nouvel élément :
ADCS Mass, numéroTPM-4. Réglez Units surkg, Threshold Value sur1.35 kg, Objective Value sur1.2 kget Improvement Direction sur Negative, ajoutez l'étiquette TPM et reliez-la à 1.2 ADCS par specified by. - Dans l'onglet TPM, sélectionnez TPM-4 ADCS Mass. Saisissez la masse de l'ADCS lue dans l'onglet Budget (Grandeur Mass, CBE + provision) comme Estimation actuelle, cliquez sur + Jalon pour ajouter
CDRavec une valeur prévue de1.3 kg, puis cliquez sur Prendre un instantané.
C'est terminé quand TPM-4 ADCS Mass est listée avec un état, un jalon CDR dans son profil prévu et un point d'instantané dans son historique d'estimations.
Vérifiez vos connaissances
- Pourquoi la provision dépend-elle de la base d'une valeur ?
- Comment la marge est-elle calculée, et quand une ligne avertit-elle ?
- Qu'apporte une TPM à un budget ?
- Qu'est-ce qui fait d'une Measure une TPM dans Holarch ?
Afficher les réponses
Pourquoi la provision dépend-elle de la base d'une valeur ?
Une estimation est moins sûre qu'un calcul, et un calcul moins qu'une mesure. La provision selon la base (15, 10 et 3 % dans la démo) prévoit davantage de réserve là où le chiffre est moins sûr.
Comment la marge est-elle calculée, et quand une ligne avertit-elle ?
La marge est l'allocation moins la meilleure estimation actuelle plus la provision. Une ligne affiche ▲ Low quand la marge est inférieure à la marge requise et ✕ Over quand elle dépasse son allocation.
Qu'apporte une TPM à un budget ?
Un budget montre l'agrégation du jour. Une TPM suit un chiffre critique sur toute la vie du projet par rapport à un profil prévu, un seuil et un objectif : une tendance vers un dépassement se voit avant les revues.
Qu'est-ce qui fait d'une Measure une TPM dans Holarch ?
L'étiquette TPM. Les Measures qui la portent sont listées dans l'onglet TPM, avec les exigences qui ont une Threshold Value.
Pour aller plus loin
Transcription
Afficher la transcription (narration et contenu de l'écran)
Introduction
Welcome back. A design is only as good as its margins. This last chapter of the track puts numbers on the dock's mass.
You will build a mass budget, and a technical performance measure that tracks it over time.
The budget
Open Architecture, then Budgets. Choose the root asset: the Bike-Share Dock. The quantity is mass, in kilograms. Every part under the dock gets a row.
On screen: Architecture → Budgets → root S.0; unit kg.
Enter each part's mass in the unit value column. A docking bay weighs fifty-five kilograms, and the dock has ten of them, so set its count to ten.
On screen: Docking Bay: 55, count 10.
The kiosk is a hundred and forty kilograms, the charging unit eighty, and the power supply thirty. The dock's row shows the sum of its parts.
On screen: Kiosk 140, Charging Unit 80, Power Supply 30.
Contingency and margin
Each value has a basis: estimated, calculated or measured. Contingency follows the basis, so a guess carries more than a part that has been weighed. Here every value is still an estimate.
On screen: Basis and contingency columns.
Set the allocation on the dock: nine hundred kilograms, the most the installation site can carry. The status says over: with fifteen percent contingency on every estimate, the dock comes to nine hundred and twenty kilograms, twenty over.
On screen: Allocation 900 on S.0 → Over allocation.
The docking bays are the biggest item. Once a bay has been weighed, its basis is measured, and its contingency drops to three percent. Set the docking bay's basis to Measured.
On screen: Docking Bay → Basis: Measured.
Now the dock is forty-six kilograms under its allocation, a margin of five percent. The project asks for ten, so the status still warns: the design needs either lighter parts or a larger allocation.
On screen: Margin 46 kg (5.11%) → Margin below 10%.
A technical performance measure
A budget is today's number. A technical performance measure, a TPM, tracks one critical number over the life of the project. Create a Measure in the Database: Dock Mass, numbered TPM one, in kilograms.
On screen: Database → New Entity: Measure TPM-1 Dock Mass.
Its threshold is nine hundred kilograms, the limit it must not pass, and its objective is eight hundred, the value the design aims for. For mass, lower is better, so its improvement direction is negative.
On screen: Units, Threshold 900, Objective 800, Improvement Direction.
What makes it a TPM is its label. Under Labels, click plus Label, and choose TPM.
On screen: Labels → + Label → TPM.
Back in Budgets, open the TPMs tab. Dock Mass is listed, with its threshold and objective.
On screen: Budgets → TPMs.
Track it
Enter the current estimate from the budget, eight hundred and fifty-four kilograms. Add a milestone: the preliminary design review on the first of December, planned at eight hundred and eighty. Take a snapshot, and today's estimate joins the history. At every review, the chart shows whether the dock is on track, long before anything is built.
On screen: Current estimate; + Milestone; Take Snapshot.
Recap
Let's recap. You built a mass budget from the parts with counts, bases and contingency, set an allocation and read the margin, and created a TPM with a threshold, an objective, a milestone and a snapshot.
That completes Behavior and Architecture. You can now model functions and their flow, action diagrams, allocation, interfaces, simulation, budgets and TPMs.
On screen: Track complete card, then end card.