Capítulos do curso
Treinamento · Trilha 3. Comportamento e arquitetura · Capítulo 3.6 de 6
3.6 Orçamentos e TPMs 3:31
Consolide a massa da estação com contingência e margem e depois acompanhe-a como medida de desempenho técnico.
Mostra o Holarch 2.13.
O que você vai aprender
- Configurar um orçamento em um asset raiz com uma grandeza, uma unidade e uma margem exigida
- Inserir valores com uma base e ver como a contingência e a margem mudam
- Definir uma alocação e ler o status de margem de uma linha
- Criar uma TPM com um limiar, um objetivo, um marco e um instantâneo
Monte um orçamento de massa da Bike-Share Dock a partir das suas partes, com quantidades, bases e contingência, defina uma alocação e leia a margem; depois crie uma medida de desempenho técnico para a massa da estação com um limiar, um objetivo, um marco planejado e um instantâneo.
Arquivos de projeto
- Projeto inicial (.holarch.json; Gerenciar projetos → Arquivos de projeto ▾ → Importar projeto (.json)…)
- Projeto concluído (.holarch.json; Gerenciar projetos → Arquivos de projeto ▾ → Importar projeto (.json)…)
O vídeo é reproduzido a partir de holarch.app; veja a Política de Privacidade.
Prática
Faça isto você mesmo no Holarch, no projeto de demonstração CubeSat EO-1.
- Abra seu projeto de demonstração EO-1 ou crie-o: Gerenciar projetos → Arquivos de projeto ▾ → Novo projeto de demonstração → CubeSat (engenharia de sistemas guiada).
- Abra Arquitetura → Orçamentos e TPMs. Na aba Orçamento, mantenha 1 EO-1 Spacecraft como raiz e mude Grandeza para Consumo de potência.
- Encontre 1.1 Payload Camera (6,2 W, Estimado) e mude sua Base para Medido. Veja como sua contingência e a margem da espaçonave mudam.
- No Banco de dados, crie um Measure com + Novo item:
ADCS Mass, númeroTPM-4. Defina Unidades comokg, Threshold Value como1.35 kg, Objective Value como1.2 kge Improvement Direction como Negative, adicione o rótulo TPM e vincule-o a 1.2 ADCS com specified by. - Na aba TPMs, selecione TPM-4 ADCS Mass. Digite a massa do ADCS da aba Orçamento (Grandeza Massa, CBE + contingência) como Estimativa atual, clique em + Marco para adicionar
CDRcom um valor planejado de1.3 kge depois clique em Registrar instantâneo.
Você terminou quando TPM-4 ADCS Mass estiver listada com um status, um marco CDR no seu perfil planejado e um ponto de instantâneo no seu histórico de estimativas.
Teste-se
- Por que a contingência depende da base de um valor?
- Como a margem é calculada e quando uma linha emite um aviso?
- O que uma TPM acrescenta a um orçamento?
- O que torna um Measure uma TPM no Holarch?
Mostrar as respostas
Por que a contingência depende da base de um valor?
Uma estimativa é menos certa que um cálculo, e um cálculo menos que uma medição. A contingência por base (15, 10 e 3% no demo) reserva mais folga onde o número é menos certo.
Como a margem é calculada e quando uma linha emite um aviso?
A margem é a alocação menos a melhor estimativa atual mais a contingência. Uma linha mostra ▲ Baixa quando a margem está abaixo da margem exigida e ✕ Acima quando excede sua alocação.
O que uma TPM acrescenta a um orçamento?
Um orçamento mostra a consolidação de hoje. Uma TPM acompanha um número crítico ao longo da vida do projeto em relação a um perfil planejado, um limiar e um objetivo, de modo que uma tendência de violação aparece antes das revisões.
O que torna um Measure uma TPM no Holarch?
O rótulo TPM. Os Measures com ele são listados na aba TPMs, junto com os requisitos que têm um Threshold Value.
Saiba mais
Transcrição
Mostrar a transcrição (narração e o que aparece na tela)
Introduction
Welcome back. A design is only as good as its margins. This last chapter of the track puts numbers on the dock's mass.
You will build a mass budget, and a technical performance measure that tracks it over time.
The budget
Open Architecture, then Budgets. Choose the root asset: the Bike-Share Dock. The quantity is mass, in kilograms. Every part under the dock gets a row.
On screen: Architecture → Budgets → root S.0; unit kg.
Enter each part's mass in the unit value column. A docking bay weighs fifty-five kilograms, and the dock has ten of them, so set its count to ten.
On screen: Docking Bay: 55, count 10.
The kiosk is a hundred and forty kilograms, the charging unit eighty, and the power supply thirty. The dock's row shows the sum of its parts.
On screen: Kiosk 140, Charging Unit 80, Power Supply 30.
Contingency and margin
Each value has a basis: estimated, calculated or measured. Contingency follows the basis, so a guess carries more than a part that has been weighed. Here every value is still an estimate.
On screen: Basis and contingency columns.
Set the allocation on the dock: nine hundred kilograms, the most the installation site can carry. The status says over: with fifteen percent contingency on every estimate, the dock comes to nine hundred and twenty kilograms, twenty over.
On screen: Allocation 900 on S.0 → Over allocation.
The docking bays are the biggest item. Once a bay has been weighed, its basis is measured, and its contingency drops to three percent. Set the docking bay's basis to Measured.
On screen: Docking Bay → Basis: Measured.
Now the dock is forty-six kilograms under its allocation, a margin of five percent. The project asks for ten, so the status still warns: the design needs either lighter parts or a larger allocation.
On screen: Margin 46 kg (5.11%) → Margin below 10%.
A technical performance measure
A budget is today's number. A technical performance measure, a TPM, tracks one critical number over the life of the project. Create a Measure in the Database: Dock Mass, numbered TPM one, in kilograms.
On screen: Database → New Entity: Measure TPM-1 Dock Mass.
Its threshold is nine hundred kilograms, the limit it must not pass, and its objective is eight hundred, the value the design aims for. For mass, lower is better, so its improvement direction is negative.
On screen: Units, Threshold 900, Objective 800, Improvement Direction.
What makes it a TPM is its label. Under Labels, click plus Label, and choose TPM.
On screen: Labels → + Label → TPM.
Back in Budgets, open the TPMs tab. Dock Mass is listed, with its threshold and objective.
On screen: Budgets → TPMs.
Track it
Enter the current estimate from the budget, eight hundred and fifty-four kilograms. Add a milestone: the preliminary design review on the first of December, planned at eight hundred and eighty. Take a snapshot, and today's estimate joins the history. At every review, the chart shows whether the dock is on track, long before anything is built.
On screen: Current estimate; + Milestone; Take Snapshot.
Recap
Let's recap. You built a mass budget from the parts with counts, bases and contingency, set an allocation and read the margin, and created a TPM with a threshold, an objective, a milestone and a snapshot.
That completes Behavior and Architecture. You can now model functions and their flow, action diagrams, allocation, interfaces, simulation, budgets and TPMs.
On screen: Track complete card, then end card.