Holarch
فصول الدورة

التدريب · المسار 4. المستندات والمخرجات · الفصل 4.2 من 5

4.2 المصفوفات الحية في المستندات 2:48

أدرج جداول RVTM وRTM تعيد بناء نفسها من النموذج.

يعرض Holarch 1.27.

→ 4.1 قوالب المستندات · كل الفصول · 4.3 مخرجات Word وExcel ←

ما ستتعلمه

  • أدرج مصفوفة حية في نص مستند واختر نطاقها
  • اقرأ الفجوات التي تبرزها المصفوفة
  • سدّ فجوة في النموذج وشاهد المصفوفة تتحدث
  • سمِّ المصفوفات القياسية وما تعدّه كل منها فجوة

استبدل جدول التحقق الفارغ في مواصفة Bike-Share Dock بمصفوفة حية لتتبع التحقق من المتطلبات، واختر نطاقها، واقرأ الفجوات التي تبرزها، وسدّ إحداها في النموذج وشاهد المصفوفة تتحدث، ثم أضف مصفوفة تتبع المتطلبات بالطريقة نفسها.

ملفات المشاريع

  • مشروع البداية (.holarch.json؛ إدارة المشاريع ← ملفات المشروع ▾ ← استيراد مشروع (.json)…)
  • المشروع المكتمل (.holarch.json؛ إدارة المشاريع ← ملفات المشروع ▾ ← استيراد مشروع (.json)…)

يُشغَّل الفيديو من holarch.app؛ راجع سياسة الخصوصية.

التطبيق العملي

نفّذ هذا بنفسك في Holarch، على المشروع التوضيحي CubeSat EO-1.

  1. افتح مشروع EO-1 التوضيحي الخاص بك، أو أنشئه: إدارة المشاريع ← ملفات المشروع ▾ ← مشروع توضيحي جديد ← CubeSat (هندسة أنظمة موجّهة).
  2. افتح الاحتياجات والمتطلبات ← المستندات ← EO-1 System Requirements Specification وانقر وصف القسم 2 Attitude Determination and Control لتعديله.
  3. في شريط أدوات النص المنسَّق، افتح + واختر مصفوفة…. واختر مصفوفة تخصيص المتطلبات، وأبقِ النطاق على هذا المستند، وانقر إدراج واضغط ⌘ / Ctrl↵ للحفظ.
  4. اقرأ التسمية التوضيحية والصفوف المظللة. 2.5 Safe Mode Recovery فجوة: لا شيء يحققه.
  5. حدّد 2.5، وفي قسم التتبع الخاص به، اربط F10 Enter Safe Mode تحت satisfied by. ثم عد إلى القسم 2 واقرأ المصفوفة مجددًا.

تنتهي حين يسرد صف 2.5 في مصفوفة التخصيص F10 Enter Safe Mode ولا يعود مظللًا.

اختبر نفسك

  1. كيف تختلف المصفوفة الحية عن جدول تكتبه؟
  2. لماذا تسد الفجوة في النموذج، لا في المصفوفة؟
  3. ما النطاقات التي يمكن أن تغطيها المصفوفة؟
إظهار الإجابات
  1. كيف تختلف المصفوفة الحية عن جدول تكتبه؟

    لا تحفظ الكتلة إلا المصفوفة والنطاق اللذين يجب عرضهما. ويعيد Holarch بناء الصفوف من النموذج في كل مرة يُعرض فيها المستند أو يُصدَّر، فلا تصبح قديمة أبدًا.

  2. لماذا تسد الفجوة في النموذج، لا في المصفوفة؟

    لا يمكن تعديل المصفوفة الحية خلية بخلية. فالفجوة رابط أو سمة مفقودة في النموذج، وإصلاحها هناك يحدّث كل مصفوفة وطريقة عرض تعرضها.

  3. ما النطاقات التي يمكن أن تغطيها المصفوفة؟

    عناصر مستند واحد، أو كل أجزاء مجموعة، أو المشروع كله. ويمكن لمصفوفتي الواجهات وN² أيضًا تغطية أبناء Asset أو Action واحد.

قراءة المزيد

النص المكتوب

إظهار النص المكتوب (التعليق الصوتي وما يظهر على الشاشة)

Introduction

Chapter two: live matrices in documents. Reviewers ask for traceability and verification matrices. In Holarch you don't fill them in by hand: a matrix in a document is rebuilt from the model whenever it is shown or exported.

You will insert a verification matrix into a specification, choose its scope, read the gaps it highlights, close a gap in the model, and add a traceability matrix.

Insert a matrix

Open the Bike-Share Dock system requirements. Its template ends with a verification approach, and section 11.1, Verification Matrix, holds an empty table to fill in by hand.

On screen: Documents → the SRS → Outline → 11.1 Verification Matrix.

Replace it with a live matrix. Click the section's text to edit it, select the empty table, and delete it.

On screen: Edit 11.1 → select → delete.

Open the plus menu, and choose Matrix. Pick the Requirements Verification Traceability Matrix. The scope starts on this document, which holds three of the project's six requirements. Choose Whole project, to cover them all.

On screen: + → Matrix… → RVTM → Scope: Whole project.

The preview lists each requirement with its verification method, its level, the test cases that verify it, and its status. Click Insert, then press Command Return to save the text.

On screen: Insert → Save.

Read the gaps

The matrix sits in the document with a dashed outline. Two rows are shaded as gaps. Show Available Bikes has a method but no test case yet. Anchored Without Digging has no verification method at all.

On screen: The live RVTM in 11.1, two gaps.

Close a gap

Close one gap in the model. Go to section 10, and select 10.2, Anchored Without Digging. In the inspector, click + Label and choose Inspection. The verification method is both a label and an attribute, so either one sets it.

On screen: Outline → 10.2 → inspector + Label → Inspection.

Go back to the matrix. The row for 10.2 now shows Inspection, without touching the matrix. It is still shaded, because no test case verifies it yet: the matrix shows the model as it is.

On screen: Outline → 11.1: the 10.2 row now shows Inspection.

Add an RTM

Add a traceability matrix the same way. Go to section 12, Traceability, edit its text, and insert the Requirements Traceability Matrix for the whole project: each requirement with its parent, the needs it traces from, what it traces to, and what satisfies it.

On screen: 12 Traceability → + → Matrix… → RTM → Whole project → Insert → Save.

Recap

The verification cross-reference matrix, with one column per method, works the same way. Let's recap. You inserted live matrices, chose their scope, read the gaps, and closed one in the model.

Next, you turn the document and its matrices into Word and Excel files.