Holarch
فصول الدورة

التدريب · المسار 9. أساسيات SysML v2 · الفصل 9.2 من 8

9.2 المنافذ والواجهات 3:44

عرّف المنافذ والواجهات، واربط الأجزاء في النص، وارسم واجهة في عرض.

يعرض Holarch 2.22.

ما ستتعلمه

  • عرّف منفذًا بسمات ذات اتجاه واقرنه باستخدام `~`
  • عرّف واجهة طرفاها منمّطان بمنافذ
  • اربط الأجزاء باستخدام واجهة واربط منفذ حدود بمنفذ جزء داخلي
  • أنشئ Interconnection View وارسم واجهة بين منفذين

عرّف منافذ SysML v2 وواجهاتها في Holarch، باتباع البرنامج التعليمي Ports and Interfaces الخاص بـ SysML v2 على مشروع Hybrid Car صغير: تعريف منفذ باتجاهات، ومنفذ مقترن، وتعريف واجهة بطرفين، ومجموعة نقل حركة أجزاؤها مربوطة بواجهات وربط، وInterconnection View لها، وواجهة مرسومة في العرض يكتبها Holarch في النص. SysML علامة تجارية مسجلة لشركة Object Management Group, Inc.

ملفات المشاريع

  • المشروع المكتمل (.holarch.json؛ إدارة المشاريع ← ملفات المشروع ▾ ← استيراد مشروع (.json)…)

يُشغَّل الفيديو من holarch.app؛ راجع سياسة الخصوصية.

التطبيق العملي

نفّذ هذا بنفسك في Holarch، على مشروع Hybrid Car التوضيحي (SysML v2).

  1. افتح مشروع Hybrid Car التوضيحي (أنشئه إذا لزم الأمر: إدارة المشاريع ← ملفات المشروع ▾ ← مشروع توضيحي جديد ← Hybrid Car (SysML v2))، وافتح النموذج ← المحرر والحزمة Vehicles.
  2. تحت interface def HighVoltageBus، أضف interface def ControlLink { end commander : ~ControlPort; end unit : ControlPort; }.
  3. في part def Powertrain، استبدل connect controller.engineCtl to engine.ecu; بـ interface engineControl : ControlLink connect controller.engineCtl to engine.ecu;، وأضف part auxBattery : Battery; بعد part battery : Battery;.
  4. افتح البنية ← عروض Interconnection والعرض powertrainConnections. اسحب من مقبض المنفذ powerOut الخاص بـ auxBattery إلى منفذ المحرك powerIn واختر واجهة : HighVoltageBus.
  5. حدد الخط الجديد وأدخل auxBus في الاسم في لوحة الخصائص. ثم افتح النموذج ← المحرر واعثر على السطر الذي كتبه Holarch في Powertrain.

تكون قد انتهيت عندما يحتوي Powertrain على interface engineControl : ControlLink … والواجهة auxBus من العرض، وتُبلغ الحالة تحت المحرر بعدم وجود مشكلات.

اختبر نفسك

  1. للمحرك port fuelIn : ~FuelPort;. ما الذي تغيّره علامة التلدة؟
  2. ما الفرق بين bind output = transmission.output; وinterface fuel : FuelLine connect tank.fuelOut to engine.fuelIn;؟
  3. لماذا يعرض العرض «واجهة : HighVoltageBus» عندما تسحب من powerOut الخاص ببطارية إلى powerIn الخاص بالمحرك؟
إظهار الإجابات
  1. للمحرك port fuelIn : ~FuelPort;. ما الذي تغيّره علامة التلدة؟

    يقرن المنفذ: لمنفذ المحرك الخصائص نفسها التي لـ FuelPort مع عكس الاتجاهات، فيصل out attribute flowRate الخاص بـ FuelPort إلى المحرك كمدخل.

  2. ما الفرق بين bind output = transmission.output; وinterface fuel : FuelLine connect tank.fuelOut to engine.fuelIn;؟

    يقول الربط إن الخاصيتين هما الشيء نفسه: منفذ حدود مجموعة نقل الحركة هو مخرج ناقل الحركة. أما استخدام الواجهة فيربط منفذين مختلفين، ويحدد تعريف الواجهة الخاص به المنافذ التي يقبلها طرفاه.

  3. لماذا يعرض العرض «واجهة : HighVoltageBus» عندما تسحب من powerOut الخاص ببطارية إلى powerIn الخاص بالمحرك؟

    يعرض Holarch تعريفات الواجهات التي يناسب طرفاها كلا المنفذين. ولـ HighVoltageBus الطرفان source : PowerPort وload : ~PowerPort، اللذان يطابقان المنفذين.

قراءة المزيد

النص المكتوب

إظهار النص المكتوب (التعليق الصوتي وما يظهر على الشاشة)

Introduction

Chapter two: ports and interfaces. A port is where a part meets the world outside it. An interface says which ports may connect.

In this chapter you define a port and an interface, connect parts in a powertrain, and draw an interface in a view.

Start the tutorial

Start the tutorial Ports and Interfaces from Project Files, Start a Tutorial. Its starter project holds the car's components with their torque and power ports, two interface definitions, and nothing yet for fuel.

On screen: Project Files ▾ → Start a Tutorial… → SysML v2: Ports and Interfaces → Start.

Ports

Above the torque port, define the fuel port. A port definition lists what crosses the port. Out means the flow rate leaves the part that owns the port.

On screen: Below FuelKind; type port def FuelPort.

The tank owns a fuel port. The engine takes fuel in, so its port is conjugated with a tilde: the same features, with in and out reversed.

On screen: FuelTank: port fuelOut : FuelPort; Engine: port fuelIn : ~FuelPort;

Interfaces

An interface definition says which ports may connect. Below the high voltage bus, define the fuel line, with a supply end and a conjugated consumer end.

On screen: Below HighVoltageBus; type interface def FuelLine.

Connect the parts

Now the powertrain: a part definition made of parts. Its own output port is bound to the transmission's output, so the two are one and the same.

On screen: After Transmission; type part def Powertrain with five parts, a port and bind.

Connect the tank to the engine with a fuel line. A dotted name reaches into a part: from the tank's fuel out, to the engine's fuel in.

On screen: In Powertrain after part transmission: interface fuel : FuelLine connect tank.fuelOut to engine.fuelIn;

The engine and the motor both drive the transmission, through a shaft each.

On screen: Two shaft interfaces.

The status under the editor says the text is applied, with no problems.

On screen: Applied, No problems.

The Interconnection View

Now see the powertrain as a view. Open Architecture, then Interconnection Views, and click New Diagram. Keep Interconnection View, choose the powertrain under Shows, and click Create.

On screen: Architecture → Interconnection Views → + New Diagram; Shows: Vehicles::Powertrain; Create.

The parts sit inside the frame with their ports on their sides. Each line is an interface from the text, and the output port on the frame is bound to the transmission.

On screen: The view.

Draw an interface

The battery does not feed the motor yet. Drag from the battery's power out port to the motor's power in. Holarch offers what fits both ports: choose Interface, High Voltage Bus.

On screen: Select battery.powerOut; drag its handle to motor.powerIn → Interface : HighVoltageBus.

Select the new line, and name it H V Bus in the inspector.

On screen: Click the new line; inspector Name: hvBus.

Close the inspector and open the text again. Holarch wrote the interface into the powertrain, with its name, its type and both ends.

On screen: Inspector ×; Model → Editor: the interface hvBus line in Powertrain.

Recap

Every step is ticked off. Click Mark as Done.

On screen: Step panel → Mark as Done.

Let's recap. You defined a port with a direction, conjugated it for the engine, defined an interface with two ends, connected the powertrain's parts in text, and drew an interface that Holarch wrote back into the text.

Next, actions and flows describe what the car does.