Holarch
Kurs bölümleri

Eğitim · Kurs 4. Belgeler ve teslimatlar · Bölüm 4.2 / 5

4.2 Belgelerde canlı matrisler 2:48

Modelden kendiliğinden yeniden oluşan RVTM ve RTM tabloları ekleyin.

Holarch 1.27'yi gösterir.

Neler öğreneceksiniz

  • Bir belgenin metnine canlı bir matris ekleyin ve kapsamını seçin
  • Bir matrisin vurguladığı boşlukları okuyun
  • Modelde bir boşluğu kapatın ve matrisin güncellendiğini görün
  • Standart matrisleri ve her birinin neyi boşluk olarak işaretlediğini sayın

Bike-Share Dock şartnamesindeki boş doğrulama tablosunu canlı bir gereksinim doğrulama izlenebilirlik matrisiyle değiştirin, kapsamını seçin, vurguladığı boşlukları okuyun, birini modelde kapatıp matrisin güncellenmesini izleyin, ardından aynı şekilde bir gereksinim izlenebilirlik matrisi ekleyin.

Proje dosyaları

  • Başlangıç projesi (.holarch.json; Projeleri yönet → Proje dosyaları ▾ → Proje içe aktar (.json)…)
  • Bitmiş proje (.holarch.json; Projeleri yönet → Proje dosyaları ▾ → Proje içe aktar (.json)…)

Video holarch.app'ten oynatılır; bkz. Gizlilik Politikası.

Alıştırma

Bunu Holarch'ta, CubeSat EO-1 demo projesinde kendiniz yapın.

  1. EO-1 demo projenizi açın veya oluşturun: Projeleri yönet → Proje dosyaları ▾ → Yeni demo proje → CubeSat (Rehberli sistem mühendisliği).
  2. İhtiyaçlar ve gereksinimler → Belgeler → EO-1 System Requirements Specification'ı açın ve düzenlemek için 2 Attitude Determination and Control bölümünün açıklamasına tıklayın.
  3. Zengin metin araç çubuğunda +'yı açın ve Matris…'i seçin. Gereksinim tahsis matrisi'ni seçin, kapsamı bu belgede bırakın, Ekle'ye tıklayın ve kaydetmek için ⌘ / Ctrl↵'a basın.
  4. Başlığı ve gölgeli satırları okuyun. 2.5 Safe Mode Recovery bir boşluktur: onu hiçbir şey karşılamıyor.
  5. 2.5'i seçin ve İzleme bölümünde satisfied by altına F10 Enter Safe Mode'u bağlayın. Bölüm 2'ye geri dönün ve matrisi yeniden okuyun.

Tahsis matrisinin 2.5 satırı F10 Enter Safe Mode'u listelediğinde ve artık gölgeli olmadığında işiniz bitmiştir.

Kendinizi sınayın

  1. Canlı bir matrisin yazdığınız bir tablodan farkı nedir?
  2. Bir boşluğu neden matriste değil de modelde kapatırsınız?
  3. Bir matris hangi kapsamları içerebilir?
Yanıtları göster
  1. Canlı bir matrisin yazdığınız bir tablodan farkı nedir?

    Blok yalnızca hangi matrisin ve kapsamın gösterileceğini saklar. Holarch, belge her gösterildiğinde veya dışa aktarıldığında satırları modelden yeniden oluşturur; bu yüzden asla güncelliğini yitirmez.

  2. Bir boşluğu neden matriste değil de modelde kapatırsınız?

    Canlı bir matris hücre hücre düzenlenemez. Boşluk, modelde eksik bir bağlantı veya özniteliktir ve onu orada düzeltmek onu gösteren her matrisi ve görünümü günceller.

  3. Bir matris hangi kapsamları içerebilir?

    Tek bir belgenin öğeleri, bir derlemenin tüm bölümleri veya projenin tamamı. Arayüz ve N² matrisleri bir Asset'in veya Action'ın alt öğelerini de kapsayabilir.

Daha fazla bilgi

Döküm

Dökümü göster (anlatım ve ekranda görünenler)

Introduction

Chapter two: live matrices in documents. Reviewers ask for traceability and verification matrices. In Holarch you don't fill them in by hand: a matrix in a document is rebuilt from the model whenever it is shown or exported.

You will insert a verification matrix into a specification, choose its scope, read the gaps it highlights, close a gap in the model, and add a traceability matrix.

Insert a matrix

Open the Bike-Share Dock system requirements. Its template ends with a verification approach, and section 11.1, Verification Matrix, holds an empty table to fill in by hand.

On screen: Documents → the SRS → Outline → 11.1 Verification Matrix.

Replace it with a live matrix. Click the section's text to edit it, select the empty table, and delete it.

On screen: Edit 11.1 → select → delete.

Open the plus menu, and choose Matrix. Pick the Requirements Verification Traceability Matrix. The scope starts on this document, which holds three of the project's six requirements. Choose Whole project, to cover them all.

On screen: + → Matrix… → RVTM → Scope: Whole project.

The preview lists each requirement with its verification method, its level, the test cases that verify it, and its status. Click Insert, then press Command Return to save the text.

On screen: Insert → Save.

Read the gaps

The matrix sits in the document with a dashed outline. Two rows are shaded as gaps. Show Available Bikes has a method but no test case yet. Anchored Without Digging has no verification method at all.

On screen: The live RVTM in 11.1, two gaps.

Close a gap

Close one gap in the model. Go to section 10, and select 10.2, Anchored Without Digging. In the inspector, click + Label and choose Inspection. The verification method is both a label and an attribute, so either one sets it.

On screen: Outline → 10.2 → inspector + Label → Inspection.

Go back to the matrix. The row for 10.2 now shows Inspection, without touching the matrix. It is still shaded, because no test case verifies it yet: the matrix shows the model as it is.

On screen: Outline → 11.1: the 10.2 row now shows Inspection.

Add an RTM

Add a traceability matrix the same way. Go to section 12, Traceability, edit its text, and insert the Requirements Traceability Matrix for the whole project: each requirement with its parent, the needs it traces from, what it traces to, and what satisfies it.

On screen: 12 Traceability → + → Matrix… → RTM → Whole project → Insert → Save.

Recap

The verification cross-reference matrix, with one column per method, works the same way. Let's recap. You inserted live matrices, chose their scope, read the gaps, and closed one in the model.

Next, you turn the document and its matrices into Word and Excel files.