Holarch
פרקי הקורס

הדרכה · מסלול 4. מסמכים ותוצרים · פרק 4.2 מתוך 5

4.2 מטריצות חיות במסמכים 2:48

הוספת טבלאות RVTM ו-RTM שבונות את עצמן מחדש מהמודל.

מציג את Holarch 1.27.

→ 4.1 תבניות מסמכים · כל הפרקים · 4.3 פלט Word ו-Excel ←

מה תלמדו

  • להוסיף מטריצה חיה לטקסט של מסמך ולבחור את ההיקף שלה
  • לקרוא את הפערים שמטריצה מדגישה
  • לסגור פער במודל ולראות את המטריצה מתעדכנת
  • לנקוב בשמות המטריצות התקניות ובמה שכל אחת מסמנת כפער

מחליפים את טבלת האימות הריקה במפרט של Bike-Share Dock במטריצת עקיבות חיה לאימות דרישות, בוחרים את ההיקף שלה, קוראים את הפערים שהיא מדגישה, סוגרים אחד מהם במודל ורואים את המטריצה מתעדכנת, ואז מוסיפים באותה דרך מטריצת עקיבות דרישות.

קובצי פרויקט

  • פרויקט התחלה (.holarch.json; ניהול פרויקטים ← קובצי פרויקט ▾ ← ייבוא פרויקט (.json)…)
  • פרויקט גמור (.holarch.json; ניהול פרויקטים ← קובצי פרויקט ▾ ← ייבוא פרויקט (.json)…)

הסרטון מוצג מ-holarch.app; ראו את מדיניות הפרטיות.

תרגול

עשו זאת בעצמכם ב-Holarch, על פרויקט ההדגמה CubeSat EO-1.

  1. פותחים את פרויקט ההדגמה EO-1, או יוצרים אותו: ניהול פרויקטים ← קובצי פרויקט ▾ ← פרויקט הדגמה חדש ← CubeSat (הנדסת מערכות מודרכת).
  2. פותחים את צרכים ודרישות ← מסמכים ← EO-1 System Requirements Specification ולוחצים על התיאור של הסעיף 2 Attitude Determination and Control כדי לערוך אותו.
  3. בסרגל הכלים של הטקסט העשיר פותחים את + ובוחרים מטריצה…. בוחרים מטריצת הקצאת דרישות, משאירים את ההיקף על המסמך הזה, לוחצים על הוספה ולוחצים ⌘ / Ctrl↵ כדי לשמור.
  4. קוראים את הכיתוב ואת השורות המוצללות. 2.5 Safe Mode Recovery הוא פער: דבר אינו מקיים אותו.
  5. בוחרים את 2.5, ובקטע עקיבות שלה מקשרים את F10 Enter Safe Mode תחת satisfied by. חוזרים לסעיף 2 וקוראים שוב את המטריצה.

סיימתם כששורת 2.5 של מטריצת ההקצאה מפרטת את F10 Enter Safe Mode וכבר אינה מוצללת.

בדיקה עצמית

  1. במה מטריצה חיה שונה מטבלה שמקלידים?
  2. למה סוגרים פער במודל ולא במטריצה?
  3. אילו היקפים מטריצה יכולה לכסות?
הצגת התשובות
  1. במה מטריצה חיה שונה מטבלה שמקלידים?

    הבלוק שומר רק איזו מטריצה ואיזה היקף להציג. ‏Holarch בונה מחדש את השורות מהמודל בכל פעם שהמסמך מוצג או מיוצא, כך שהוא לעולם אינו מתיישן.

  2. למה סוגרים פער במודל ולא במטריצה?

    אי אפשר לערוך מטריצה חיה תא אחר תא. הפער הוא קישור או מאפיין שחסרים במודל, ותיקונו שם מעדכן כל מטריצה ותצוגה שמציגה אותו.

  3. אילו היקפים מטריצה יכולה לכסות?

    הפריטים של מסמך אחד, כל החלקים של מסמך מקובץ, או הפרויקט כולו. מטריצות הממשקים וה-N² יכולות גם לכסות את הילדים של Asset או Action אחד.

קריאה נוספת

תמליל

הצגת התמליל (הקריינות ומה שמוצג על המסך)

Introduction

Chapter two: live matrices in documents. Reviewers ask for traceability and verification matrices. In Holarch you don't fill them in by hand: a matrix in a document is rebuilt from the model whenever it is shown or exported.

You will insert a verification matrix into a specification, choose its scope, read the gaps it highlights, close a gap in the model, and add a traceability matrix.

Insert a matrix

Open the Bike-Share Dock system requirements. Its template ends with a verification approach, and section 11.1, Verification Matrix, holds an empty table to fill in by hand.

On screen: Documents → the SRS → Outline → 11.1 Verification Matrix.

Replace it with a live matrix. Click the section's text to edit it, select the empty table, and delete it.

On screen: Edit 11.1 → select → delete.

Open the plus menu, and choose Matrix. Pick the Requirements Verification Traceability Matrix. The scope starts on this document, which holds three of the project's six requirements. Choose Whole project, to cover them all.

On screen: + → Matrix… → RVTM → Scope: Whole project.

The preview lists each requirement with its verification method, its level, the test cases that verify it, and its status. Click Insert, then press Command Return to save the text.

On screen: Insert → Save.

Read the gaps

The matrix sits in the document with a dashed outline. Two rows are shaded as gaps. Show Available Bikes has a method but no test case yet. Anchored Without Digging has no verification method at all.

On screen: The live RVTM in 11.1, two gaps.

Close a gap

Close one gap in the model. Go to section 10, and select 10.2, Anchored Without Digging. In the inspector, click + Label and choose Inspection. The verification method is both a label and an attribute, so either one sets it.

On screen: Outline → 10.2 → inspector + Label → Inspection.

Go back to the matrix. The row for 10.2 now shows Inspection, without touching the matrix. It is still shaded, because no test case verifies it yet: the matrix shows the model as it is.

On screen: Outline → 11.1: the 10.2 row now shows Inspection.

Add an RTM

Add a traceability matrix the same way. Go to section 12, Traceability, edit its text, and insert the Requirements Traceability Matrix for the whole project: each requirement with its parent, the needs it traces from, what it traces to, and what satisfies it.

On screen: 12 Traceability → + → Matrix… → RTM → Whole project → Insert → Save.

Recap

The verification cross-reference matrix, with one column per method, works the same way. Let's recap. You inserted live matrices, chose their scope, read the gaps, and closed one in the model.

Next, you turn the document and its matrices into Word and Excel files.