فصول الدورة
التدريب · المسار 14. جداول البيانات · الفصل 14.4 من 5
14.4 المخططات البيانية وبيانات النموذج 2:47
أنشئ مخططًا بيانيًا لنطاق ونسّق محوره، وأدرج «جدول نموذج» حيًا، واقرأ قيم النموذج باستخدام SUMIFS وHOLARCH.VALUE.
يعرض Holarch 2.35.
ما ستتعلمه
- أنشئ مخططًا بيانيًا لنطاق وانقله بجوار البيانات
- اضبط حدود المحور ووحداته في «تنسيق المحور»
- أدرج «جدول نموذج» لبيانات النموذج الحية
- اجمع قيم النموذج باستخدام SUMIFS واقرأ قيمة واحدة باستخدام HOLARCH.VALUE
- شاهد تغييرًا في النموذج ينتقل إلى الورقة والمخطط البياني
أنشئ مخططًا بيانيًا لميزانية كتلة EO-1 واربطها بالنموذج: أدرج مخططًا بيانيًا عموديًا لكتل الأنظمة الفرعية واضبط محور قيمه في «تنسيق المحور»، وأدرج «جدول نموذج» حيًا للقراءة فقط لكل أصل برقمه وكتلته، واستبدل التقديرات المكتوبة بـ SUMIFS على الجدول، واقرأ تخصيص الكتلة من النموذج باستخدام HOLARCH.VALUE، ثم غيّر كتلة في النموذج وشاهد الميزانية تتبعها.
ملفات المشاريع
- مشروع البداية (.holarch.json؛ إدارة المشاريع ← ملفات المشروع ▾ ← استيراد مشروع (.json)…)
- المشروع المكتمل (.holarch.json؛ إدارة المشاريع ← ملفات المشروع ▾ ← استيراد مشروع (.json)…)
يُشغَّل الفيديو من holarch.app؛ راجع سياسة الخصوصية.
التطبيق العملي
نفّذ هذا بنفسك في Holarch، على CubeSat EO-1.
- افتح ملف البداية للفصل، أو مصنفك من الفصل 14.3.
- حدد B2:C8، وافتح مخطط بياني واختر عمودي. اسحب المخطط البياني إلى يمين الميزانية.
- انقر بزر الماوس الأيمن على المخطط البياني، واختر تنسيق المحور العمودي…، واضبط الحد الأقصى على
5والوحدة الرئيسية على1. - أضف ورقة باسم
Model. في A1، انقر جدول النموذج…، واختر الفئة الأصل، وحدد الرقم والكتلة، وسمّهPartsثم انقر إدراج. - في الميزانية، اكتب
=SUMIFS(Parts[Mass],Parts[Number],A3&"*")في C3 واملأها لأسفل حتى C8. وفي Assumptions، اكتب=HOLARCH.VALUE("Spacecraft Mass","Threshold Value","kg")في B1. - في قاعدة البيانات، غيّر كتلة Payload Camera من 2.4 إلى 2.9 kg وعُد إلى جدول البيانات.
تكون قد انتهيت عندما تأتي الكتل من النموذج، ويقرأ التخصيص 12 من النموذج، وتتبع المجاميع والهامش والمخطط البياني تغيير Payload Camera.
اختبر نفسك
- هل يستطيع جدول بيانات تغيير النموذج؟
- ماذا يطابق A3&"*" في معايير SUMIFS؟
- أين تضبط الحد الأقصى لمحور مخطط بياني ووحدته الرئيسية؟
إظهار الإجابات
هل يستطيع جدول بيانات تغيير النموذج؟
لا. جداول النموذج ودوال HOLARCH تقرأ النموذج؛ ولا يكتب جدول البيانات فيه أبدًا.
ماذا يطابق A3&"*" في معايير SUMIFS؟
كل رقم جزء يبدأ برقم النظام الفرعي، مثل 1.1.1 و1.1.2 للرقم 1.1.
أين تضبط الحد الأقصى لمحور مخطط بياني ووحدته الرئيسية؟
في «تنسيق المحور»، الذي يُفتح من قائمة النقر بزر الماوس الأيمن على المخطط البياني؛ والمربع الفارغ يُبقي القيمة تلقائية.
قراءة المزيد
النص المكتوب
إظهار النص المكتوب (التعليق الصوتي وما يظهر على الشاشة)
Introduction
Chapter four: charts and model data. A chart shows the budget at a glance. And a spreadsheet can read the model, so the budget stays current without retyping.
In this chapter you chart the budget, then feed it from the model.
Charts
Select the subsystems and their masses, B2 to C8. Open Chart, and choose Column.
On screen: Name Box B2:C8 → Chart ▾ → Column.
The chart floats over the sheet. Drag it to the right of the budget, so the totals stay in view.
On screen: Drag the chart right of column E.
The chart follows its cells. Right-click it for its menu, and choose Format Vertical Axis.
On screen: Right-click the chart → Format Vertical Axis….
Format Axis sets the bounds and units. Set the maximum to five and the major unit to one. Leave a box empty to keep it automatic. Close the panel.
On screen: Maximum 5, Major 1 → close.
Model data
The masses so far are typed estimates. The model holds the current mass of every component, so read them from there. Add a sheet, and name it Model.
On screen: + → Model.
Select A1, and click Model Table. Choose the class Asset, tick Number and Mass, name the table Parts, and click Insert.
On screen: A1 → Model Table… → Class Asset; Number, Mass; name Parts → Insert.
The table lists every asset with its number and mass, live and read-only. A spreadsheet reads the model, and never writes to it.
On screen: The Parts table.
Back in the budget, replace the estimate in C3. The SUMIFS function adds the masses of the parts whose number starts with the subsystem's number.
On screen: Budget → C3: =SUMIFS(Parts[Mass],Parts[Number],A3&"*") ↵.
Fill it down to C8. Every subsystem now adds up its components from the model.
On screen: Name Box C3:C8 → Fill ▾ → Fill Down.
HOLARCH.VALUE reads one value of one item, in the unit you ask for. On the Assumptions sheet, the allocation becomes the threshold of the spacecraft mass measure in the model.
On screen: Assumptions → B1: =HOLARCH.VALUE("Spacecraft Mass","Threshold Value","kg") ↵.
The sheet follows the model
Now change the model. In the Database, open the payload camera's mass, and change it from two point four to two point nine kilograms.
On screen: Database → Payload Camera → Mass 2.4 → 2.9.
Back in the spreadsheet, with its editor tab. The payload camera's mass, the totals, the margin and the chart have all followed, with no edit to the sheet.
On screen: Editor tab → Budget: 2.90 kg, totals, margin, chart.
Recap
To recap: chart a range and format its axis, insert a Model Table for live model data, sum it with SUMIFS, and read single values with HOLARCH.VALUE.
In the last chapter, you import an Excel workbook and get AI help with formulas.