Holarch
Kurskapitel

Schulung · Reihe 14. Tabellen · Kapitel 14.4 von 5

14.4 Diagramme und Modelldaten 2:47

Ein Diagramm aus einem Bereich erstellen und seine Achse formatieren, eine Live-Modelltabelle einfügen und Modellwerte mit SUMIFS und HOLARCH.VALUE lesen.

Zeigt Holarch 2.35.

Das lernen Sie

  • Einen Bereich als Diagramm darstellen und das Diagramm neben die Daten verschieben
  • Achsengrenzen und Einheiten unter „Achse formatieren“ festlegen
  • Eine Modelltabelle mit Live-Modelldaten einfügen
  • Modellwerte mit SUMIFS summieren und einen einzelnen Wert mit HOLARCH.VALUE lesen
  • Sehen, wie eine Modelländerung in die Tabelle und das Diagramm einfließt

Das EO-1-Massenbudget darstellen und mit dem Modell verbinden: ein Säulendiagramm der Subsystemmassen einfügen und seine Werteachse unter „Achse formatieren“ festlegen, eine schreibgeschützte Live-Modelltabelle aller Assets mit Nummer und Masse einfügen, die getippten Schätzungen durch SUMIFS über die Tabelle ersetzen, die Massenzuordnung mit HOLARCH.VALUE aus dem Modell lesen, dann eine Masse im Modell ändern und sehen, wie das Budget folgt.

Projektdateien

  • Startprojekt (.holarch.json; Projekte verwalten → Projektdateien ▾ → Projekt importieren (.json)…)
  • Fertiges Projekt (.holarch.json; Projekte verwalten → Projektdateien ▾ → Projekt importieren (.json)…)

Das Video wird von holarch.app abgespielt; siehe Datenschutzerklärung.

Übung

Führen Sie dies selbst in Holarch durch, an CubeSat EO-1.

  1. Öffnen Sie die Startdatei des Kapitels oder Ihre Arbeitsmappe aus Kapitel 14.3.
  2. Wählen Sie B2:C8, öffnen Sie Diagramm und wählen Sie Säule. Ziehen Sie das Diagramm rechts neben das Budget.
  3. Klicken Sie mit der rechten Maustaste auf das Diagramm, wählen Sie Vertikale Achse formatieren…, setzen Sie das Maximum auf 5 und das Hauptintervall auf 1.
  4. Fügen Sie ein Blatt namens Model hinzu. Klicken Sie in A1 auf Modelltabelle…, wählen Sie die Klasse Asset, aktivieren Sie Number und Mass, nennen Sie sie Parts und klicken Sie auf Einfügen.
  5. Geben Sie auf Budget in C3 =SUMIFS(Parts[Mass],Parts[Number],A3&"*") ein und füllen Sie nach unten bis C8 aus. Geben Sie auf Assumptions in B1 =HOLARCH.VALUE("Spacecraft Mass","Threshold Value","kg") ein.
  6. Ändern Sie in der Datenbank die Masse der Payload Camera von 2.4 auf 2.9 kg und kehren Sie zur Tabelle zurück.

Sie sind fertig, wenn die Massen aus dem Modell kommen, die Zuordnung 12 aus dem Modell liest und die Summen, die Marge und das Diagramm der Änderung an der Payload Camera folgen.

Selbsttest

  1. Kann eine Tabelle das Modell ändern?
  2. Was findet A3&"*" in den SUMIFS-Kriterien?
  3. Wo legen Sie Maximum und Hauptintervall einer Diagrammachse fest?
Antworten anzeigen
  1. Kann eine Tabelle das Modell ändern?

    Nein. Modelltabellen und HOLARCH-Funktionen lesen das Modell; die Tabelle schreibt nie hinein.

  2. Was findet A3&"*" in den SUMIFS-Kriterien?

    Jede Teilenummer, die mit der Nummer des Subsystems beginnt, zum Beispiel 1.1.1 und 1.1.2 für 1.1.

  3. Wo legen Sie Maximum und Hauptintervall einer Diagrammachse fest?

    Unter „Achse formatieren“, geöffnet über das Kontextmenü des Diagramms; ein leeres Feld lässt den Wert automatisch.

Weiterlesen

Transkript

Transkript anzeigen (Erzählung und Bildschirminhalt)

Introduction

Chapter four: charts and model data. A chart shows the budget at a glance. And a spreadsheet can read the model, so the budget stays current without retyping.

In this chapter you chart the budget, then feed it from the model.

Charts

Select the subsystems and their masses, B2 to C8. Open Chart, and choose Column.

On screen: Name Box B2:C8 → Chart ▾ → Column.

The chart floats over the sheet. Drag it to the right of the budget, so the totals stay in view.

On screen: Drag the chart right of column E.

The chart follows its cells. Right-click it for its menu, and choose Format Vertical Axis.

On screen: Right-click the chart → Format Vertical Axis….

Format Axis sets the bounds and units. Set the maximum to five and the major unit to one. Leave a box empty to keep it automatic. Close the panel.

On screen: Maximum 5, Major 1 → close.

Model data

The masses so far are typed estimates. The model holds the current mass of every component, so read them from there. Add a sheet, and name it Model.

On screen: + → Model.

Select A1, and click Model Table. Choose the class Asset, tick Number and Mass, name the table Parts, and click Insert.

On screen: A1 → Model Table… → Class Asset; Number, Mass; name Parts → Insert.

The table lists every asset with its number and mass, live and read-only. A spreadsheet reads the model, and never writes to it.

On screen: The Parts table.

Back in the budget, replace the estimate in C3. The SUMIFS function adds the masses of the parts whose number starts with the subsystem's number.

On screen: Budget → C3: =SUMIFS(Parts[Mass],Parts[Number],A3&"*") ↵.

Fill it down to C8. Every subsystem now adds up its components from the model.

On screen: Name Box C3:C8 → Fill ▾ → Fill Down.

HOLARCH.VALUE reads one value of one item, in the unit you ask for. On the Assumptions sheet, the allocation becomes the threshold of the spacecraft mass measure in the model.

On screen: Assumptions → B1: =HOLARCH.VALUE("Spacecraft Mass","Threshold Value","kg") ↵.

The sheet follows the model

Now change the model. In the Database, open the payload camera's mass, and change it from two point four to two point nine kilograms.

On screen: Database → Payload Camera → Mass 2.4 → 2.9.

Back in the spreadsheet, with its editor tab. The payload camera's mass, the totals, the margin and the chart have all followed, with no edit to the sheet.

On screen: Editor tab → Budget: 2.90 kg, totals, margin, chart.

Recap

To recap: chart a range and format its axis, insert a Model Table for live model data, sum it with SUMIFS, and read single values with HOLARCH.VALUE.

In the last chapter, you import an Excel workbook and get AI help with formulas.