Holarch
कोर्स के अध्याय

प्रशिक्षण · ट्रैक 3. व्यवहार और आर्किटेक्चर · 6 में से अध्याय 3.4

3.4 इंटरफ़ेस 2:31

हर इंटरफ़ेस को एक स्थिति, एक स्वामी और एक क्षमता दें, उस पर आइटम ले जाएं, और ICD निर्यात करें।

Holarch 1.27 दिखाता है।

← 3.3 आवंटन · सभी अध्याय · 3.5 सिमुलेशन →

आप क्या सीखेंगे

  • इंटरफ़ेस रजिस्टर पढ़ें और उसे इंटरफ़ेस स्थिति के अनुसार फ़िल्टर करें
  • इंस्पेक्टर में किसी इंटरफ़ेस की स्थिति, स्वामी, माध्यम और क्षमता सेट करें
  • ले जाए जाने वाले आइटम को डेटा दर दें और क्षमता जांच पढ़ें
  • किसी इंटरफ़ेस का ICD Word में निर्यात करें और किसी सिस्टम का I² आरेख खोलें

इंटरफ़ेस रजिस्टर में Bike-Share Dock के इंटरफ़ेस प्रबंधित करें: सेलुलर डेटा लिंक पर स्थिति, स्वामी और क्षमता सेट करें, उस पर ले जाए जाने वाले आइटम को डेटा दर दें, क्षमता जांच पढ़ें, इंटरफ़ेस नियंत्रण दस्तावेज़ निर्यात करें, और I² आरेख में डॉक के इंटरफ़ेस देखें।

प्रोजेक्ट फ़ाइलें

वीडियो holarch.app से चलता है; गोपनीयता नीति देखें।

अभ्यास

इसे Holarch में CubeSat EO-1 डेमो प्रोजेक्ट पर स्वयं करें।

  1. अपना EO-1 डेमो प्रोजेक्ट खोलें, या उसे बनाएं: प्रोजेक्ट प्रबंधित करें → प्रोजेक्ट फ़ाइलें ▾ → नया डेमो प्रोजेक्ट → CubeSat (गाइडेड सिस्टम्स इंजीनियरिंग)।
  2. इंटरफ़ेस → इंटरफ़ेस रजिस्टर खोलें और प्रस्तावित कार्ड पर क्लिक करें। पंक्ति IF-14.1 Customer Portal पर क्लिक करें।
  3. इंस्पेक्टर में इंटरफ़ेस स्थिति को सहमत, स्वामी को Ground Segment Lead और माध्यम को HTTPS पर सेट करें। उसकी 1000 Mbps की क्षमता रहने दें।
  4. इंटरफ़ेस → आइटम और I/O खोलें, Image Product (वह आइटम जिसे पोर्टल स्थानांतरित करता है) चुनें, और डेटा दर को 50 तथा डेटा दर इकाइयां को Mbps पर सेट करें। रजिस्टर में वापस, IF-14.1 के क्षमता कॉलम पर पॉइंटर ले जाएं और जांच पढ़ें। इंटरफ़ेस नियंत्रण दस्तावेज़ निर्यात करने के लिए उसकी पंक्ति पर ICD पर क्लिक करें।
  5. डेटाबेस में 1 EO-1 Spacecraft चुनें और इसमें खोलें ▾ → I2 आरेख चुनें। वह सेल खोजें जिसमें IF-01 Payload Power Line है।
  6. जांचे गए चरण-दर-चरण अभ्यास के लिए ट्यूटोरियल 7 Interfaces चलाएं (सहायता → ट्यूटोरियल)।

आपका काम तब पूरा है जब IF-14.1 स्वामी और माध्यम सेट के साथ सहमत है, उसकी क्षमता जांच OK दिखाती है, और आपके पास ICD Word फ़ाइल है।

स्वयं जांचें

  1. Holarch कैसे तय करता है कि कोई कंड्यूट अपने आइटम ले जा सकता है या नहीं?
  2. डेटा दर आइटम पर क्यों होती है, कंड्यूट पर क्यों नहीं?
  3. प्रस्तावित या सहमत जैसी इंटरफ़ेस स्थिति पाठक को क्या बताती है?
  4. I² आरेख की एक सेल में क्या होता है?
उत्तर दिखाएं
  1. Holarch कैसे तय करता है कि कोई कंड्यूट अपने आइटम ले जा सकता है या नहीं?

    यह कंड्यूट द्वारा स्थानांतरित हर आइटम की Data Rate (या Size) जोड़ता है, हर एक को कंड्यूट की इकाइयों में बदलता है और योग की तुलना Capacity से करता है। परिणाम OK, Over capacity, Unit mismatch या No capacity होता है।

  2. डेटा दर आइटम पर क्यों होती है, कंड्यूट पर क्यों नहीं?

    दर बताती है कि क्या ले जाया जा रहा है, और एक ही आइटम कई कंड्यूट से जा सकता है। हर कंड्यूट की जांच उसके द्वारा ले जाए गए आइटम का योग उसकी अपनी क्षमता से मिलाती है।

  3. प्रस्तावित या सहमत जैसी इंटरफ़ेस स्थिति पाठक को क्या बताती है?

    दोनों छोरों की टीमें कहाँ तक पहुँची हैं: ड्राफ़्ट और प्रस्तावित लिखे जा चुके हैं पर अभी दोनों पक्षों ने स्वीकार नहीं किए हैं, सहमत का अर्थ है दोनों इसे स्वीकार करते हैं, और बेसलाइन किया गया अंतिम चरण है। रजिस्टर के कार्ड हर स्थिति की गिनती दिखाते हैं।

  4. I² आरेख की एक सेल में क्या होता है?

    उसकी पंक्ति और कॉलम के दो चाइल्ड एसेट के बीच के कंड्यूट: पंक्ति उद्गम छोर है और कॉलम दूसरा छोर।

और पढ़ें

ट्रांसक्रिप्ट

ट्रांसक्रिप्ट दिखाएं (नरेशन और स्क्रीन पर क्या है)

Introduction

Welcome back. The dock's parts connect through interfaces: a power cable, a data link. This chapter manages them.

You will work in the Interface Register, the list of every interface in the project.

The register

Open Interfaces, then Interface Register. Each conduit from Getting Started is a row: the cellular data link between the kiosk and the back office, and the power cable from the power supply to the charging unit. Neither has a status yet.

On screen: Interfaces → Interface Register.

Status, owner and capacity

Select the cellular data link. In the inspector, set its interface status to Proposed: the kiosk team has written it down, and the back office team has not agreed to it yet. Its owner is the back office team.

On screen: Cellular Data Link → Interface Status: Proposed; Owner.

Give it a capacity: sixty-four kilobits per second, and set its medium to cellular LTE.

On screen: Capacity 64, Units kbit/s, Medium.

Items it carries

Now say what the link carries. The unlock code from Rent a Bike travels from the back office to the kiosk over this link. In its Trace section, show all relations, and under transfers, link Unlock Code.

On screen: Trace → Show all relations → transfers + → Link existing… → Unlock Code.

For the capacity check, the item needs a data rate. Select Unlock Code in the Database and set its data rate: two kilobits per second.

On screen: Database → Unlock Code → Data Rate 2 kbit/s.

The capacity check

Back in the register, the row counts the item it carries, and the capacity check says OK: two kilobits per second on a link of sixty-four. If the items ever carried more than the link can, the check would turn red.

On screen: Register → capacity check.

ICD and I²

The interface control document is one click away. ICD exports this interface as a Word document for the other team, generated from the model, so it agrees with the design.

On screen: ICD → Word export.

For the whole dock, open the I squared diagram. Select the Bike-Share Dock in the Database, choose Open in, then I2 Diagram. The parts sit on the diagonal, and each cell between two parts holds the interfaces that join them.

On screen: Database → S.0 → Open in ▾ → I2 Diagram.

Recap

Let's recap. You read the register, gave an interface a status, an owner and a capacity, related the item it carries, let the capacity check compare them, exported the ICD, and opened the I squared diagram.

Next, you put numbers on Rent a Bike, and simulate it.