Holarch
Kurskapitel

Schulung · Reihe 3. Verhalten und Architektur · Kapitel 3.4 von 6

3.4 Schnittstellen 2:31

Jeder Schnittstelle einen Status, einen Verantwortlichen und eine Kapazität geben, Elemente über sie transportieren und das ICD exportieren.

Zeigt Holarch 1.27.

← 3.3 Zuordnung · Alle Kapitel · 3.5 Simulation →

Das lernen Sie

  • Das Schnittstellenregister lesen und nach Schnittstellenstatus filtern
  • Status, Verantwortlichen, Medium und Kapazität einer Schnittstelle im Inspektor festlegen
  • Einem transportierten Element eine Datenrate geben und die Kapazitätsprüfung ablesen
  • Das ICD einer Schnittstelle nach Word exportieren und das I²-Diagramm eines Systems öffnen

Verwalten Sie die Schnittstellen des Bike-Share Dock im Schnittstellenregister: Status, Verantwortlichen und Kapazität der Mobilfunk-Datenverbindung festlegen, dem transportierten Element eine Datenrate geben, die Kapazitätsprüfung ablesen, das Schnittstellensteuerungsdokument exportieren und die Schnittstellen der Station im I²-Diagramm ansehen.

Projektdateien

  • Startprojekt (.holarch.json; Projekte verwalten → Projektdateien ▾ → Projekt importieren (.json)…)
  • Fertiges Projekt (.holarch.json; Projekte verwalten → Projektdateien ▾ → Projekt importieren (.json)…)

Das Video wird von holarch.app abgespielt; siehe Datenschutzerklärung.

Übung

Führen Sie dies selbst in Holarch durch, am Demoprojekt CubeSat EO-1.

  1. Öffnen Sie Ihr EO-1-Demoprojekt oder erstellen Sie es: Projekte verwalten → Projektdateien ▾ → Neues Demoprojekt → CubeSat (Geführtes Systems Engineering).
  2. Öffnen Sie Schnittstellen → Schnittstellenregister und klicken Sie auf die Karte Proposed. Klicken Sie auf die Zeile IF-14.1 Customer Portal.
  3. Setzen Sie im Inspektor Interface Status auf Agreed, Owner auf Ground Segment Lead und Medium auf HTTPS. Behalten Sie die Capacity von 1000 Mbps bei.
  4. Öffnen Sie Schnittstellen → Elemente & I/O, wählen Sie Image Product aus (das Element, das das Portal überträgt), und setzen Sie Data Rate auf 50 und Data Rate Units auf Mbps. Zeigen Sie zurück im Register auf die Spalte Capacity von IF-14.1 und lesen Sie die Prüfung. Klicken Sie in ihrer Zeile auf ICD, um das Schnittstellensteuerungsdokument zu exportieren.
  5. Wählen Sie 1 EO-1 Spacecraft in der Datenbank aus und wählen Sie Öffnen in ▾ → I2-Diagramm. Suchen Sie die Zelle mit IF-01 Payload Power Line.
  6. Für eine geprüfte Schritt-für-Schritt-Anleitung führen Sie Tutorial 7 Interfaces aus (Hilfe → Tutorials).

Sie sind fertig, wenn IF-14.1 Agreed ist, Owner und Medium gesetzt sind, ihre Kapazitätsprüfung OK anzeigt und Sie die ICD-Word-Datei haben.

Selbsttest

  1. Wie entscheidet Holarch, ob ein Conduit seine Elemente transportieren kann?
  2. Warum gehört die Datenrate zum Element und nicht zum Conduit?
  3. Was sagt ein Schnittstellenstatus wie Proposed oder Agreed einem Leser?
  4. Was enthält eine Zelle des I²-Diagramms?
Antworten anzeigen
  1. Wie entscheidet Holarch, ob ein Conduit seine Elemente transportieren kann?

    Es addiert die Data Rate (oder Size) jedes Elements, das der Conduit überträgt, rechnet jede in die Einheiten des Conduits um und vergleicht die Summe mit Capacity. Das Ergebnis ist OK, Over capacity, Unit mismatch oder No capacity.

  2. Warum gehört die Datenrate zum Element und nicht zum Conduit?

    Die Rate beschreibt, was transportiert wird, und dasselbe Element kann über mehrere Conduits laufen. Die Prüfung jedes Conduits summiert die Elemente, die er transportiert, gegen seine eigene Kapazität.

  3. Was sagt ein Schnittstellenstatus wie Proposed oder Agreed einem Leser?

    Wie weit die Teams an beiden Enden gekommen sind: Draft und Proposed sind niedergeschrieben, aber noch nicht von beiden Seiten akzeptiert, Agreed bedeutet, dass beide sie akzeptieren, und Baselined ist die letzte Stufe. Die Karten des Registers zählen jeden Status.

  4. Was enthält eine Zelle des I²-Diagramms?

    Die Conduits zwischen den beiden Kind-Assets ihrer Zeile und Spalte: Die Zeile ist das Ursprungsende und die Spalte das andere Ende.

Weiterlesen

Transkript

Transkript anzeigen (Erzählung und Bildschirminhalt)

Introduction

Welcome back. The dock's parts connect through interfaces: a power cable, a data link. This chapter manages them.

You will work in the Interface Register, the list of every interface in the project.

The register

Open Interfaces, then Interface Register. Each conduit from Getting Started is a row: the cellular data link between the kiosk and the back office, and the power cable from the power supply to the charging unit. Neither has a status yet.

On screen: Interfaces → Interface Register.

Status, owner and capacity

Select the cellular data link. In the inspector, set its interface status to Proposed: the kiosk team has written it down, and the back office team has not agreed to it yet. Its owner is the back office team.

On screen: Cellular Data Link → Interface Status: Proposed; Owner.

Give it a capacity: sixty-four kilobits per second, and set its medium to cellular LTE.

On screen: Capacity 64, Units kbit/s, Medium.

Items it carries

Now say what the link carries. The unlock code from Rent a Bike travels from the back office to the kiosk over this link. In its Trace section, show all relations, and under transfers, link Unlock Code.

On screen: Trace → Show all relations → transfers + → Link existing… → Unlock Code.

For the capacity check, the item needs a data rate. Select Unlock Code in the Database and set its data rate: two kilobits per second.

On screen: Database → Unlock Code → Data Rate 2 kbit/s.

The capacity check

Back in the register, the row counts the item it carries, and the capacity check says OK: two kilobits per second on a link of sixty-four. If the items ever carried more than the link can, the check would turn red.

On screen: Register → capacity check.

ICD and I²

The interface control document is one click away. ICD exports this interface as a Word document for the other team, generated from the model, so it agrees with the design.

On screen: ICD → Word export.

For the whole dock, open the I squared diagram. Select the Bike-Share Dock in the Database, choose Open in, then I2 Diagram. The parts sit on the diagonal, and each cell between two parts holds the interfaces that join them.

On screen: Database → S.0 → Open in ▾ → I2 Diagram.

Recap

Let's recap. You read the register, gave an interface a status, an owner and a capacity, related the item it carries, let the capacity check compare them, exported the ICD, and opened the I squared diagram.

Next, you put numbers on Rent a Bike, and simulate it.