Holarch
Rozdziały kursu

Szkolenia · Ścieżka 3. Zachowanie i architektura · Rozdział 3.4 z 6

3.4 Interfejsy 2:31

Nadaj każdemu interfejsowi status, właściciela i przepustowość, przenoś przez niego elementy i wyeksportuj ICD.

Pokazuje Holarch 1.27.

← 3.3 Alokacja · Wszystkie rozdziały · 3.5 Symulacja →

Czego się nauczysz

  • Odczytywanie Rejestru interfejsów i filtrowanie go według statusu interfejsu
  • Ustawianie statusu, właściciela, medium i przepustowości interfejsu w inspektorze
  • Nadawanie przenoszonemu elementowi przepływności i odczytywanie kontroli przepustowości
  • Eksportowanie ICD interfejsu do Word i otwieranie diagramu I² systemu

Zarządzaj interfejsami stacji Bike-Share Dock w Rejestrze interfejsów: ustaw status, właściciela i przepustowość łącza danych komórkowych, nadaj przenoszonemu przez nie elementowi przepływność, odczytaj kontrolę przepustowości, wyeksportuj dokument kontroli interfejsów i zobacz interfejsy stacji na diagramie I².

Pliki projektu

  • Projekt początkowy (.holarch.json; Zarządzaj projektami → Pliki projektu ▾ → Importuj projekt (.json)…)
  • Projekt ukończony (.holarch.json; Zarządzaj projektami → Pliki projektu ▾ → Importuj projekt (.json)…)

Film jest odtwarzany z holarch.app; zobacz Politykę prywatności.

Ćwiczenie

Wykonaj to samodzielnie w Holarch, w projekcie demonstracyjnym CubeSat EO-1.

  1. Otwórz swój projekt demonstracyjny EO-1 lub go utwórz: Zarządzaj projektami → Pliki projektu ▾ → Nowy projekt demonstracyjny → CubeSat (inżynieria systemów z przewodnikiem).
  2. Otwórz Interfejsy → Rejestr interfejsów i kliknij kartę Proposed. Kliknij wiersz IF-14.1 Customer Portal.
  3. W inspektorze ustaw Interface Status na Agreed, Właściciel na Ground Segment Lead i Średni na HTTPS. Pozostaw Capacity 1000 Mbps.
  4. Otwórz Interfejsy → Elementy i we/wy, zaznacz Image Product (element przesyłany przez portal) i ustaw Data Rate na 50, a Data Rate Units na Mbps. Po powrocie do rejestru wskaż kolumnę Capacity interfejsu IF-14.1 i odczytaj wynik kontroli. Kliknij ICD w jego wierszu, aby wyeksportować dokument kontroli interfejsów.
  5. Zaznacz 1 EO-1 Spacecraft w Bazie danych i wybierz Otwórz w ▾ → Diagram I2. Znajdź komórkę zawierającą IF-01 Payload Power Line.
  6. Aby przejść całość ze sprawdzaniem, uruchom samouczek 7 Interfejsy (Pomoc → Samouczki).

Gotowe, gdy IF-14.1 ma status Agreed z ustawionymi polami Właściciel i Medium, jego kontrola przepustowości pokazuje OK, a ty masz plik Word z ICD.

Sprawdź się

  1. Jak Holarch rozstrzyga, czy conduit może przenosić swoje elementy?
  2. Dlaczego przepływność należy do elementu, a nie do conduit?
  3. Co status interfejsu, taki jak Proposed lub Agreed, mówi czytelnikowi?
  4. Co zawiera komórka diagramu I²?
Pokaż odpowiedzi
  1. Jak Holarch rozstrzyga, czy conduit może przenosić swoje elementy?

    Sumuje Data Rate (lub Size) każdego elementu przesyłanego przez conduit, przelicza każdą wartość na jednostki conduit i porównuje sumę z Capacity. Wynik to OK, Przekroczona przepustowość, Niezgodność jednostek lub Brak przepustowości.

  2. Dlaczego przepływność należy do elementu, a nie do conduit?

    Przepływność opisuje to, co jest przenoszone, a ten sam element może przechodzić przez kilka conduit. Kontrola każdego conduit sumuje przenoszone przez niego elementy względem jego własnej Capacity.

  3. Co status interfejsu, taki jak Proposed lub Agreed, mówi czytelnikowi?

    Jak daleko doszły zespoły po obu stronach: Draft i Proposed są zapisane, ale jeszcze nie zaakceptowane przez obie strony, Agreed oznacza, że obie strony je akceptują, a Baselined to etap końcowy. Karty rejestru zliczają każdy status.

  4. Co zawiera komórka diagramu I²?

    Conduit między dwoma zasobami podrzędnymi z jej wiersza i kolumny: wiersz to koniec źródłowy, a kolumna drugi koniec.

Więcej informacji

Transkrypcja

Pokaż transkrypcję (narracja i to, co widać na ekranie)

Introduction

Welcome back. The dock's parts connect through interfaces: a power cable, a data link. This chapter manages them.

You will work in the Interface Register, the list of every interface in the project.

The register

Open Interfaces, then Interface Register. Each conduit from Getting Started is a row: the cellular data link between the kiosk and the back office, and the power cable from the power supply to the charging unit. Neither has a status yet.

On screen: Interfaces → Interface Register.

Status, owner and capacity

Select the cellular data link. In the inspector, set its interface status to Proposed: the kiosk team has written it down, and the back office team has not agreed to it yet. Its owner is the back office team.

On screen: Cellular Data Link → Interface Status: Proposed; Owner.

Give it a capacity: sixty-four kilobits per second, and set its medium to cellular LTE.

On screen: Capacity 64, Units kbit/s, Medium.

Items it carries

Now say what the link carries. The unlock code from Rent a Bike travels from the back office to the kiosk over this link. In its Trace section, show all relations, and under transfers, link Unlock Code.

On screen: Trace → Show all relations → transfers + → Link existing… → Unlock Code.

For the capacity check, the item needs a data rate. Select Unlock Code in the Database and set its data rate: two kilobits per second.

On screen: Database → Unlock Code → Data Rate 2 kbit/s.

The capacity check

Back in the register, the row counts the item it carries, and the capacity check says OK: two kilobits per second on a link of sixty-four. If the items ever carried more than the link can, the check would turn red.

On screen: Register → capacity check.

ICD and I²

The interface control document is one click away. ICD exports this interface as a Word document for the other team, generated from the model, so it agrees with the design.

On screen: ICD → Word export.

For the whole dock, open the I squared diagram. Select the Bike-Share Dock in the Database, choose Open in, then I2 Diagram. The parts sit on the diagonal, and each cell between two parts holds the interfaces that join them.

On screen: Database → S.0 → Open in ▾ → I2 Diagram.

Recap

Let's recap. You read the register, gave an interface a status, an owner and a capacity, related the item it carries, let the capacity check compare them, exported the ICD, and opened the I squared diagram.

Next, you put numbers on Rent a Bike, and simulate it.