Rozdziały kursu
Szkolenia · Ścieżka 9. Podstawy SysML v2 · Rozdział 9.2 z 8
9.2 Porty i interfejsy 3:44
Definiowanie portów i interfejsów, łączenie części w tekście i rysowanie interfejsu w widoku.
Pokazuje Holarch 2.22.
Czego się nauczysz
- Definiowanie portu z atrybutami kierunkowymi i sprzęganie go za pomocą `~`
- Definiowanie interfejsu, którego końce są typowane portami
- Łączenie części użyciem interfejsu i wiązanie portu brzegowego z portem części wewnętrznej
- Tworzenie Widoku połączeń i rysowanie interfejsu między dwoma portami
Definiuj porty i interfejsy SysML v2 w Holarch zgodnie z samouczkiem SysML v2 Porty i interfejsy na małym projekcie Hybrid Car: definicja portu z kierunkami, port sprzężony, definicja interfejsu z dwoma końcami, układ napędowy, którego części są połączone interfejsami i wiązaniem, jego Widok połączeń oraz interfejs narysowany w widoku, który Holarch zapisuje w tekście. SysML jest zastrzeżonym znakiem towarowym Object Management Group, Inc.
Pliki projektu
- Projekt ukończony (.holarch.json; Zarządzaj projektami → Pliki projektu ▾ → Importuj projekt (.json)…)
Film jest odtwarzany z holarch.app; zobacz Politykę prywatności.
Ćwiczenie
Wykonaj to samodzielnie w Holarch na projekcie demonstracyjnym Hybrid Car (SysML v2).
- Otwórz swój projekt demonstracyjny Hybrid Car (w razie potrzeby utwórz go: Zarządzaj projektami → Pliki projektu ▾ → Nowy projekt demonstracyjny → Hybrid Car (SysML v2)), otwórz Model → Edytor i pakiet
Vehicles. - Pod
interface def HighVoltageBusdodajinterface def ControlLink { end commander : ~ControlPort; end unit : ControlPort; }. - W
part def Powertrainzastąpconnect controller.engineCtl to engine.ecu;przezinterface engineControl : ControlLink connect controller.engineCtl to engine.ecu;i dodajpart auxBattery : Battery;popart battery : Battery;. - Otwórz Architektura → Widoki połączeń i widok
powertrainConnections. Przeciągnij od uchwytu portupowerOutelementuauxBatterydo portupowerInsilnika i wybierz Interface : HighVoltageBus. - Zaznacz nową linię i wpisz
auxBusjako jej Nazwa w inspektorze. Następnie otwórz Model → Edytor i znajdź wiersz, który Holarch zapisał wPowertrain.
Gotowe, gdy Powertrain zawiera interface engineControl : ControlLink … oraz interfejs auxBus z widoku, a stan pod edytorem nie zgłasza problemów.
Sprawdź się
- Silnik ma
port fuelIn : ~FuelPort;. Co zmienia tylda? - Czym różni się
bind output = transmission.output;odinterface fuel : FuelLine connect tank.fuelOut to engine.fuelIn;? - Dlaczego widok proponuje Interface : HighVoltageBus, gdy przeciągasz od portu
powerOutakumulatora do portupowerInsilnika?
Pokaż odpowiedzi
Silnik ma
port fuelIn : ~FuelPort;. Co zmienia tylda?Sprzęga port: port silnika ma te same cechy co FuelPort z odwróconymi kierunkami, więc
out attribute flowRatez FuelPort dociera do silnika jako wejście.Czym różni się
bind output = transmission.output;odinterface fuel : FuelLine connect tank.fuelOut to engine.fuelIn;?Wiązanie mówi, że dwie cechy są tym samym: port brzegowy układu napędowego jest wyjściem skrzyni biegów. Użycie interfejsu łączy dwa różne porty, a jego definicja interfejsu określa, jakie porty przyjmują jego końce.
Dlaczego widok proponuje Interface : HighVoltageBus, gdy przeciągasz od portu
powerOutakumulatora do portupowerInsilnika?Holarch proponuje definicje interfejsów, których końce pasują do obu portów. HighVoltageBus ma końce
source : PowerPortiload : ~PowerPort, które pasują do tych dwóch portów.
Więcej informacji
Transkrypcja
Pokaż transkrypcję (narracja i to, co widać na ekranie)
Introduction
Chapter two: ports and interfaces. A port is where a part meets the world outside it. An interface says which ports may connect.
In this chapter you define a port and an interface, connect parts in a powertrain, and draw an interface in a view.
Start the tutorial
Start the tutorial Ports and Interfaces from Project Files, Start a Tutorial. Its starter project holds the car's components with their torque and power ports, two interface definitions, and nothing yet for fuel.
On screen: Project Files ▾ → Start a Tutorial… → SysML v2: Ports and Interfaces → Start.
Ports
Above the torque port, define the fuel port. A port definition lists what crosses the port. Out means the flow rate leaves the part that owns the port.
On screen: Below FuelKind; type port def FuelPort.
The tank owns a fuel port. The engine takes fuel in, so its port is conjugated with a tilde: the same features, with in and out reversed.
On screen: FuelTank: port fuelOut : FuelPort; Engine: port fuelIn : ~FuelPort;
Interfaces
An interface definition says which ports may connect. Below the high voltage bus, define the fuel line, with a supply end and a conjugated consumer end.
On screen: Below HighVoltageBus; type interface def FuelLine.
Connect the parts
Now the powertrain: a part definition made of parts. Its own output port is bound to the transmission's output, so the two are one and the same.
On screen: After Transmission; type part def Powertrain with five parts, a port and bind.
Connect the tank to the engine with a fuel line. A dotted name reaches into a part: from the tank's fuel out, to the engine's fuel in.
On screen: In Powertrain after part transmission: interface fuel : FuelLine connect tank.fuelOut to engine.fuelIn;
The engine and the motor both drive the transmission, through a shaft each.
On screen: Two shaft interfaces.
The status under the editor says the text is applied, with no problems.
On screen: Applied, No problems.
The Interconnection View
Now see the powertrain as a view. Open Architecture, then Interconnection Views, and click New Diagram. Keep Interconnection View, choose the powertrain under Shows, and click Create.
On screen: Architecture → Interconnection Views → + New Diagram; Shows: Vehicles::Powertrain; Create.
The parts sit inside the frame with their ports on their sides. Each line is an interface from the text, and the output port on the frame is bound to the transmission.
On screen: The view.
Draw an interface
The battery does not feed the motor yet. Drag from the battery's power out port to the motor's power in. Holarch offers what fits both ports: choose Interface, High Voltage Bus.
On screen: Select battery.powerOut; drag its handle to motor.powerIn → Interface : HighVoltageBus.
Select the new line, and name it H V Bus in the inspector.
On screen: Click the new line; inspector Name: hvBus.
Close the inspector and open the text again. Holarch wrote the interface into the powertrain, with its name, its type and both ends.
On screen: Inspector ×; Model → Editor: the interface hvBus line in Powertrain.
Recap
Every step is ticked off. Click Mark as Done.
On screen: Step panel → Mark as Done.
Let's recap. You defined a port with a direction, conjugated it for the engine, defined an interface with two ends, connected the powertrain's parts in text, and drew an interface that Holarch wrote back into the text.
Next, actions and flows describe what the car does.