Kurs bölümleri
Eğitim · Kurs 3. Davranış ve mimari · Bölüm 3.3 / 6
3.3 Tahsis 2:33
Rıhtımın hangi parçasının her işlevi gerçekleştirdiğine karar verin ve geriye kalanı bulun.
Holarch 1.27'yi gösterir.
Neler öğreneceksiniz
- performed by ilişkisiyle eylemlere karşı varlıklardan oluşan bir İzlenebilirlik Matrisi kurun
- Bir işlevi, matriste tek tıklamayla onu gerçekleştiren varlığa tahsis edin
- Hiçbir varlığın gerçekleştirmediği eylemleri bulmak için Yalnızca boşluklar'ı kullanın
- Bir tahsisi öğenin İzleme bölümünde doğrulayın
Bike-Share Dock'un işlevlerini ve Rent a Bike adımlarını, performed by ilişkisiyle eylemlere karşı varlıklardan oluşan bir matriste onları gerçekleştiren parçalara tahsis edin; ardından hâlâ gerçekleştireni olmayanları listelemek için Yalnızca boşluklar'ı kullanın.
Proje dosyaları
- Başlangıç projesi (.holarch.json; Projeleri yönet → Proje dosyaları ▾ → Proje içe aktar (.json)…)
- Bitmiş proje (.holarch.json; Projeleri yönet → Proje dosyaları ▾ → Proje içe aktar (.json)…)
Video holarch.app'ten oynatılır; bkz. Gizlilik Politikası.
Alıştırma
Bunu Holarch'ta, CubeSat EO-1 demo projesinde kendiniz yapın.
- EO-1 demo projenizi açın veya oluşturun: Projeleri yönet → Proje dosyaları ▾ → Yeni demo proje → CubeSat (Rehberli sistem mühendisliği).
- Doğrulama → İzlenebilirlik Matrisi'ni açın. Satırlar çipine tıklayın, Satırların kaynağı'nı Bir kök nesne altındaki hiyerarşi olarak ayarlayın ve kök olarak OPS Run Nominal Imaging Pass'i seçin, ardından Bitti'ye tıklayın.
- Sütunlar çipine tıklayın, Sütunların kaynağı'nı Asset sınıfıyla Bir sınıfın tüm nesneleri olarak ayarlayın ve İlişki'yi performed by olarak ayarlayın.
- Yalnızca boşluklar'ı işaretleyin. Sistemin bir bütün olarak gerçekleştirdiği kök OPS ile birlikte OPS.9 Hold Data Onboard kalır.
- OPS.9 Hold Data Onboard'un, faydalı yük verilerini depolamada tutan parça olan 1.4 C&DH ile kesiştiği hücreye tıklayın. Ardından Veritabanı'nda OPS.9'u seçin ve İzleme bölümündeki performed by'ı okuyun.
- Denetimli bir adım adım anlatım için 6 Physical Architecture and Allocation öğreticisini çalıştırın (Yardım → Öğreticiler).
Yalnızca boşluklar artık OPS.9'u listelemediğinde ve İzleme bölümü performed by 1.4 C&DH gösterdiğinde işiniz bitmiştir.
Kendinizi sınayın
- İlişki neden İzin verilenlerin tümü yerine performed by olarak ayarlanır?
- Bir tahsis nerede saklanır?
- Yalnızca boşluklar bir satır gösteriyor. Bu her zaman bir hata mıdır?
Yanıtları göster
İlişki neden İzin verilenlerin tümü yerine performed by olarak ayarlanır?
Tek bir tür seçiliyken boş bir hücreye tıklamak tam olarak o ilişkiyi oluşturur. İzin verilen tüm türlerle, birden fazlası uygun olduğunda Holarch hangisini kastettiğinizi sormak zorundadır.
Bir tahsis nerede saklanır?
Öğelerin üzerinde: Action'da performed by, Asset'te performs olarak. Matris bu bağlantıların yalnızca bir görünümüdür; bu yüzden öğenin İzleme bölümü gibi başka herhangi bir görünüm aynı tahsisi gösterir.
Yalnızca boşluklar bir satır gösteriyor. Bu her zaman bir hata mıdır?
Hayır. Üst düzey bir operasyon veya işlev sistemin bütünü tarafından yapılabilir, bu yüzden tek bir gerçekleştiriciye ihtiyaç duymaz. Kalan her adım genellikle birine ihtiyaç duyar.
Daha fazla bilgi
Döküm
Dökümü göster (anlatım ve ekranda görünenler)
Introduction
Welcome back. Functions say what the dock does. Its parts, the assets, say what it is. Allocation joins the two.
In this chapter you allocate every function to the part that performs it.
What allocation is
Each function should be performed by a part of the system. A function nothing performs will not happen, and a part with no function is weight with no job. In the model, allocation is one relationship: performed by.
On screen: Card: allocation.
Set up the matrix
A matrix is the quickest way to allocate many functions at once. Open Verification, then Traceability Matrix.
On screen: Verification → Traceability Matrix.
Click Rows, and choose all entities of the class Action. Set Columns to the class Asset the same way. Then set the relationship to performed by, so a click on a cell creates exactly that.
On screen: Rows → class Action; Columns → class Asset; Relationship: performed by.
Allocate the functions
The top-level functions first. Three were allocated in Getting Started, and the matrix marks them: Rent a Bike by the Rental Kiosk, Return a Bike by the Docking Bay, and Charge Bikes by the Charging Unit.
On screen: Existing marks: F.1, F.2, F.3.
Allocate the other two. Take Payment is performed by the Back Office Service: click the cell where its row and that column meet. Report Dock Status is performed by the kiosk, which talks to the back office.
On screen: F.4 × S.4, F.5 × S.2.
The steps of Rent a Bike from the last chapter need performers too. Identify Rider happens at the kiosk, Check Account in the back office, and Unlock Bay in the docking bay.
On screen: F.1.1 × S.2, F.1.2 × S.4, F.1.3 × S.1.
Find the gaps
Now turn on Gaps only. The matrix keeps only the rows and columns with no link: the steps still to allocate, and the top-level function, which is done by the dock as a whole.
On screen: Gaps only.
The rest follow the same way. Show Bay Number and Start Rental belong to the kiosk and the back office, and Relock Bay to the docking bay.
On screen: F.1.4 × S.2, F.1.6 × S.4, F.1.7 × S.1.
On the item
Allocation is stored on the items, not in the matrix. Select Rent a Bike in the Database, and open its Trace section: performed by lists the Rental Kiosk.
On screen: Database → F.1 → Trace.
Recap
Let's recap. You set up a matrix of actions against assets with performed by, allocated the functions and the steps with one click each, and used Gaps only to find what was left.
Next, you define how the dock's parts connect: interfaces.